Valid8.com/ACATS VoIP Megaco extensions / H.248.x Conformance Test Suite, for use with H.248 Megaco Signaling Tester
TEST SUITE OVERVIEW
References
Archive/Project voip/Megaco_EXT_TS
Version 19171599
Date 08 Jan 2009
Number of Scenarios 43
Number of Groups 20
Average per Group 2
GROUP/SCENARIO TEST PURPOSE
Text_Mode
Text_Mode/
MG
H248_MG_TXT_Start_01 Wait for ServiceChangeReq, send response
User Action: Generate a Service Change event, "Cold Reboot"
Config: Config1
SUT: MG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2002-05 [1]
Text_Mode/
MG/
H248_2
Text_Mode/
MG/
H248_2/
BV
H248_2_MG_TXT_BV_01 Initial condition: SUT has ability to perform T38 fax calls
set up call flow, an AuditCapability Request message (for Media and Package
descriptor) is sent to determine whether the SUT can perform T38 fax. After
T38 ability is confirmed, a voice call setup is performed for two terminations,
initializing T38.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: ITU-T H.248.2
H248_2_MG_TXT_BV_01b Initial condition: SUT has ability to perform T38 fax calls

Verifies that the SUT responds to MGC Controlled T38 call set up. In this T38
set up call flow, an AuditCapability Request message (for Media and Package
descriptor) is sent to determine whether the SUT can perform T38 fax.
initializing T38.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: ITU-T H.248.2
Text_Mode/
MG/
H248_2/
BI
H248_2_MG_TXT_BI_01 Initial condition: SUT has ability to perform T38 fax calls. Termination
TID1 is not in any context.
Call Type Discrimination event field.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: ITU-T H.248.2, section 8
H248_2_MG_TXT_BI_02 Initial condition: SUT has ability to perform T38 fax calls
Termination State Property Package Name field.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: ITU-T H.248.2, section 8
H248_2_MG_TXT_BI_03 Initial condition: SUT has ability to perform T38 fax calls
IP Fax event field.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: ITU-T H.248.2, section 10
Text_Mode/
MG/
H248_3
Text_Mode/
MG/
H248_3/
BV
Text_Mode/
MG/
H248_3/
BI
Text_Mode/
MG/
H248_6
Text_Mode/
MG/
H248_6/
BV
H248_6_MG_TXT_BV_01 Initial condition: SUT has ability to use Dynamic Tone Definition package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
Ensures that the IUT specifies a new tone on a termination in an existing context
on receipt of a Transaction request containing:
Action request with
CID set to CID1
MODIFY Command request with
TID set to TID1
MEDIA DESCRIPTOR with TERMINATION STATE descriptor with the following parameters set
dtd/tid
dtd/tst
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to TID1
Initial condition: SUT has ability to use Dynamic Tone Definition package.
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.6
H248_6_MG_TXT_BV_02 Initial condition: SUT has ability to use Dynamic Tone Definition package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
Ensures that the IUT specifies a new tone for all terminations
on receipt of a Transaction request containing:
Action request with
CID set to NULL
MODIFY Command request with
TID set to ROOT
MEDIA DESCRIPTOR with TERMINATION STATE descriptor with the following parameters set
dtd/tid
dtd/tst
Action reply with
CID set to NULL
MODIFY Command reply with
TID set to ROOT
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.6
H248_6_MG_TXT_BV_03 Initial condition: SUT has ability to use Dynamic Tone Definition package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
Ensures that the IUT edits an existing tone for a termination in an existing context
on receipt of a Transaction request containing:
Action request with
CID set to CID1
MODIFY Command request with
TID set to TID1
MEDIA DESCRIPTOR with TERMINATION STATE descriptor with the following parameters set
dtd/tid = existing tone ID
dtd/tst
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to TID1
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.6
H248_6_MG_TXT_BV_04 Initial condition: SUT has ability to use Dynamic Tone Definition package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
Ensures that the IUT edits an existing tone for a terminations
on receipt of a Transaction request containing:
Action request with
CID set to NULL
MODIFY Command request with
TID set to ROOT
MEDIA DESCRIPTOR with TERMINATION STATE descriptor with the following parameters set
dtd/tid = existing tone ID
dtd/tst
Action reply with
CID set to NULL1
MODIFY Command reply with
TID set to ROOT
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.6
H248_6_MG_TXT_BV_05 Initial condition: SUT has ability to use Dynamic Tone Definition package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
Ensures that the IUT loses changes to a dynamically created tone
when a termination is taken out of a context.
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.6
Text_Mode/
MG/
H248_6/
BI
H248_6_MG_TXT_BI_01 Initial condition: SUT has ability to use Dynamic Tone Definition package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
Ensures that the IUT returns a protocol error on an invalid package/tone id name
on receipt of a Transaction request containing:
Action request with
CID set to NULL
MODIFY Command request with
TID set to ROOT
MEDIA DESCRIPTOR with TERMINATION STATE descriptor with the following parameters set
dtd/ttid
dtd/tst
Action reply with
CID set to NULL1
MODIFY Command reply with
TID set to ROOT
Error descriptor (e.g. value 401 "Protocol Error")
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.6
H248_6_MG_TXT_BI_02 Initial condition: SUT has ability to use Dynamic Tone Definition package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
Ensures that the IUT returns an error with an invalid tone string
on receipt of a Transaction request containing:
Action request with
CID set to NULL
MODIFY Command request with
TID set to ROOT
MEDIA DESCRIPTOR with TERMINATION STATE descriptor with the following parameters set
dtd/tid
dtd/tst = invalid formatted tone string
Action reply with
CID set to NULL
MODIFY Command reply with
TID set to ROOT
Error descriptor (e.g. value 401 "Protocol Error")
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.6
Text_Mode/
MG/
H248_8
Text_Mode/
MG/
H248_8/
BV
H248_8_MG_TXT_BV_01 Initial condition: none
Action request with
CID set to CHOOSE
ADD Command request with
TID set to an unknown physical termination ID
acceptable descriptors

sends a Transaction reply containing
Action reply with
CID set to CHOOSE
ADD Command reply with
TID set to unknown physical termination ID
Error descriptor (error 430) with unknown Termination ID in the
error text in the error descriptor.
User Action: None
Config: Config1
SUT: MG
Status: Optional
Ref: H248.8
Text_Mode/
MG/
H248_8/
BI
Text_Mode/
MG/
H248_13
Text_Mode/
MG/
H248_13/
BV
H248_13_MG_TXT_BV_01 Initial condition: SUT has ability to use Quality Alert Ceasing package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
Action request with
CID set to CID1
MODIFY Command request with
TID set to TID1
EVENT DESCRIPTOR with with the following parameters set:
nt/qualert{th=user defined value}
qac/qualertcease{th=user defined value}
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to TID1
sent a Notify Request with a qualert event for TID1 and the quality of TID1 is
back to an acceptable level.
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.13
H248_13_MG_TXT_BV_02 Initial condition: SUT has ability to use Quality Alert Ceasing package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
Action request with
CID set to CID1
MODIFY Command request with
TID set to TID1
EVENT DESCRIPTOR with with the following parameters set:
nt/qualert{th=user defined value}
qac/qualertcease{th=user defined value}
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to TID1
than the threshold level parameter and no quality alerts are outstanding.
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.13
Text_Mode/
MG/
H248_13/
BI
H248_13_MG_TXT_BI_01 Initial condition: SUT has ability to use Quality Alert Ceasing package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
event ID as the following:
Action request with
CID set to CID1
MODIFY Command request with
TID set to TID1
EVENT DESCRIPTOR with with the following parameters set:
nt/qualert{th=user defined value}
qac/qualertceaseeeed{th=user defined value}
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to TID1
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.13
H248_13_MG_TXT_BI_02 Initial condition: SUT has ability to use Quality Alert Ceasing package
2 Terminations, characterized by TID1 and TID2 within Context CID1.
threshold value as the following:
Action request with
CID set to CID1
MODIFY Command request with
TID set to TID1
EVENT DESCRIPTOR with with the following parameters set:
nt/qualert{th=user defined value}
qac/qualertcease{th=invalid value (not 0 to 99}
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to TID1
2 Terminations, characterized by TID1 and TID2 within Context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.13
Text_Mode/
MG/
H248_14
Text_Mode/
MG/
H248_14/
BV
H248_14_MG_TXT_BV_01 Initial condition: SUT supports the inactivity timer package. Set configuration
parameter, TSPX_KEEPALIVE_ON, to false;
test, an Audit Capability Request message is sent to verify the SUT supports the
"it" inactivity package. When the inactivity timer capability is verified, a
Modify Request message is sent to the SUT, modifying the ROOT termination to
have an inactivity timer. After the inactivity timer is set, the tester waits
for a time greater than the inactivity timer without sending any message to the
SUT, waiting for a Notify Request message from the SUT indicating an
inactivity timeout event. The tester replies to the Notify Request.
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: ITU-T H.248.14
H248_14_MG_TXT_BV_02 Initial condition: SUT supports the inactivity timer package
test, an Audit Capability Request message is sent to verify the SUT supports the
"it" inactivity package. When the inactivity timer capability is verified, a
Modify Request message is sent to the SUT, modifying the ROOT termination to
have an inactivity timer. After the inactivity timer is set, the tester waits
for a time greater than the inactivity timer without sending any message to the
SUT, waiting for a Notify Request message from the SUT indicating an
inactivity timeout event. The tester does not reply and waits for a response
by the SUT the follows section 11.5 in H.248.1.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: ITU-T H.248.1, H.248.14
Text_Mode/
MG/
H248_14/
BI
H248_14_MG_TXT_BI_01 Initial condition: SUT supports the inactivity timer package
In the test, a Modify Request message is sent to the SUT, modifying the ROOT termination to
have an inactivity timer that has a value greater than 65535. Tester waits for an error
reply from the SUT.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: ITU-T H.248.1, H.248.14
H248_14_MG_TXT_BI_02 Initial condition: SUT supports the inactivity timer package
2 Terminations (TID1 & TID2) exist in context CID1.
In the test, a Modify Request message is sent to the SUT, modifying the TID1 termination to
have an inactivity timer. Tester waits for an error reply from the SUT.
2 Terminations (TID1 & TID2) exist in context CID1.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: ITU-T H.248.1, H.248.14
H248_14_MG_TXT_BI_03 Initial condition: SUT supports the inactivity timer package
In the test, a Modify Request message is sent to the SUT, modifying the ROOT termination to
set the paramater it/mitInvalid to a value greater than 0, less than 65535. Tester waits
for an error reply from the SUT.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: ITU-T H.248.1, H.248.14
H248_14_MG_TXT_BI_04 Initial condition: SUT supports the inactivity timer package
In the test, a Modify Request message is sent to the SUT, modifying the ROOT termination to
have an inactivity timer that has a value greater than 65535. Tester waits for an error
reply from the SUT.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: ITU-T H.248.1, H.248.14
Text_Mode/
MG/
H248_15
Text_Mode/
MG/
H248_15/
BV
H248_15_MG_TXT_BV_01 Initial condition: A physical Termination, characterized by TID1, in the NULL Context
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
Two ADD Command request with
1st TID set to TID1
with acceptable descriptors
2nd TID set to CHOOSE
with acceptable media descriptor for creation of a RTP Termination
and to set package defined property on the local descriptor using
attribute h248item
sends a Transaction reply containing
Action reply with
CID set to a specific value (assigned by the MG)
ADD Command reply with
TID CHOOSE set to a specific value (assigned by the MG).
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: H.248.15
H248_15_MG_TXT_BV_02 Initial condition: A physical Termination, characterized by TID1, in the NULL Context
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
Two ADD Command request with
1st TID set to TID1
with acceptable descriptors
2nd TID set to CHOOSE
with acceptable media descriptor for creation of a RTP Termination
and to set package defined property on the remote descriptor using
attribute h248item
sends a Transaction reply containing
Action reply with
CID set to a specific value (assigned by the MG)
ADD Command reply with
TID CHOOSE set to a specific value (assigned by the MG).
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: H.248.15
H248_15_MG_TXT_BV_03 Initial condition: A physical Termination, characterized by TID1, in the NULL Context
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
Two ADD Command request with
1st TID set to TID1
with acceptable descriptors
2nd TID set to CHOOSE
with acceptable media descriptor for creation of a RTP Termination
and to set package defined property on the local descriptor and
remote descriptor using attribute h248item
sends a Transaction reply containing
Action reply with
CID set to a specific value (assigned by the MG)
ADD Command reply with
TID CHOOSE set to a specific value (assigned by the MG).
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: H.248.15
Text_Mode/
MG/
H248_15/
BI
H248_15_MG_TXT_BI_01 Initial condition: A physical Termination, characterized by TID1, in the NULL Context
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
Two ADD Command request with
1st TID set to TID1
with acceptable descriptors
2nd TID set to CHOOSE
with acceptable media descriptor for creation of a RTP Termination
and to set an Invalid package defined property on the local descriptor using
attribute h248item
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
ADD Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: H.248.15
H248_15_MG_TXT_BI_02 Initial condition: A physical Termination, characterized by TID1, in the NULL Context
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
Two ADD Command request with
1st TID set to TID1
with acceptable descriptors
2nd TID set to CHOOSE
with acceptable media descriptor for creation of a RTP Termination
and to set an Invalid package defined property on the remote descriptor using
attribute h248item
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
ADD Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: H.248.15
H248_15_MG_TXT_BI_03 Initial condition: A physical Termination, characterized by TID1, in the NULL Context
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
Two ADD Command request with
1st TID set to TID1
with acceptable descriptors
2nd TID set to CHOOSE
with acceptable media descriptor for creation of a RTP Termination
and to set an Invalid package defined property on the local and remote descriptor
using attribute h248item
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
ADD Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
The physical Termination TID1 shall NOT be in serviceState "outOfService".
SUT has ability to use the SDP H.238.15 Package Attribute.
User Action: None
Config: Config1
SUT: MG
Status: Mandatory
Ref: H.248.15
Text_Mode/
MG/
H248_16
Text_Mode/
MG/
H248_16/
BV
H248_16_MG_TXT_BV_01 Initial condition: SUT has ability to use Extended DTMF detection and Enhanced DTMF detection package
with the following:
CID set to NULL
TID set to TID1
Event ID set to xdd/xce
Event Parameter set to the following:
- bc = 10
- mp = "enhanced"
DigitMap set to Dialplan0=(xxxxxxx)
Action reply with
CID set to NULL
MODIFY Command reply with
TID set to TID1
message is sent indicating Observed Event with digit string "1111111".
And when digits "222"are dialed, a Notify Request message is sent indicating
Observed Event with digit string "2222222".
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.16
H248_16_MG_TXT_BV_02 Initial condition: SUT has ability to use Extended DTMF detection and Enhanced DTMF detection package
with the following:
CID set to NULL
TID set to TID1
Event ID set to xdd/xce
Parameter(s) set to the following:
- xdd = ON
- mp = "enhanced"
DigitMap set to Dialplan0=(0S|00|911|[1-7]xxx|8xxxxxxx|Fxxxxxxx|exx|91xxxxxxxxxx|9011x.S)
Action reply with
CID set to NULL
MODIFY Command reply with
TID set to TID1
message is sent indicating Observed Event with digit string "911".
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.16
H248_16_MG_TXT_BV_03 Initial condition: SUT has ability to use Extended DTMF detection and Enhanced DTMF detection package
with the following:
CID set to NULL
TID set to TID1
Event ID set to xdd/xce
Parameter(s) set to the following:
- xdd = ON
- mp = "enhanced"
DigitMap set to Dialplan0=(0S|00|911|[1-7]xxx|8xxxxxxx|Fxxxxxxx|exx|91xxxxxxxxxx|9011x.S)
Action reply with
CID set to NULL
MODIFY Command reply with
TID set to TID1
message is sent indicating Observed Event with digit string "911" and
parameter, extra = "0101."
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.16
Text_Mode/
MG/
H248_16/
BI
H248_16_MG_TXT_BI_01 Initial condition: SUT has ability to use Extended DTMF detection and Enhanced DTMF detection package
with the following:
CID set to NULL
TID set to TID1
Event ID set to dd/xce
DigitMap set to Dialplan0=(xxxxxxx)
Action reply with
CID set to NULL
ADD Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol error")
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.16
H248_16_MG_TXT_BI_02 Initial condition: SUT has ability to use Extended DTMF detection and Enhanced DTMF detection package
with the following:
CID set to NULL
TID set to TID1
Event ID set to dd/ce
Parameter(s) set to the following:
- bc = 10
DigitMap set to Dialplan0=(xxxxxxx)
Action reply with
CID set to NULL
ADD Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol error")
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.16
H248_16_MG_TXT_BI_03 Initial condition: SUT has ability to use Extended DTMF detection and Enhanced DTMF detection package
with the following:
CID set to NULL
TID set to TID1
Event ID set to dd/ce
Parameter(s) set to the following:
- xdd = ON
DigitMap set to Dialplan0=(xxxxxxx)
Action reply with
CID set to NULL
ADD Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol error")
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.16
H248_16_MG_TXT_BI_04 Initial condition: SUT has ability to use Extended DTMF detection and Enhanced DTMF detection package
with the following:
CID set to NULL
TID set to TID1
Event ID set to dd/ce
Parameter(s) set to the following:
- mp = "enhanced"
DigitMap set to Dialplan0=(xxxxxxx)
Action reply with
CID set to NULL
ADD Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol error")
User Action: None
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.16
Text_Mode/
MG/
H248_17
Text_Mode/
MG/
H248_17/
BV
Text_Mode/
MG/
H248_17/
BI
Text_Mode/
MG/
H248_23
Text_Mode/
MG/
H248_23/
BV
Text_Mode/
MG/
H248_23/
BI
Text_Mode/
MG/
H248_25
Text_Mode/
MG/
H248_25/
BV
H248_25_MG_TXT_BV_01 Initial condition: SUT has ability to use the H.248.25/basic CAS package
an Events Descriptor for the seize event with specific RequestID was set using
the basic CAS package at the IUT for a specific physical Termination (TID1)
in the NULL Context. The IUT has detected the seize event.
Request containing:
Action request with
CID set to NULL
NOTIFY Command request with
TID set to TSPX_H248_25_TID1
ObservedEvents Descriptor
specific RequestID
observed event = bcas/sz
an Events Descriptor for the seize event with specific RequestID was set using
the basic CAS package at the IUT for a specific physical Termination (TID1)
in the NULL Context. The IUT has detected the seize event.
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.25
Text_Mode/
MG/
H248_25/
BI
Text_Mode/
MG/
H248_26
Text_Mode/
MG/
H248_26/
BV
H248_26_MG_TXT_BV_01 Initial condition: SUT has ability to use the H.248.26/ package
Action request with
CID set to CID1
MODIFY Command request with
TID set to TSPX_H248_26_TID1
signal descriptor for signal xal/las
sends a Transaction Reply containing
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to TID1

Config: Config1
SUT: MG
Status: Extension
Ref: H.246.26
Text_Mode/
MG/
H248_26/
BI
Text_Mode/
MG/
H248_28
Text_Mode/
MG/
H248_28/
BV
H248_28_MG_TXT_BV_01 Initial condition: SUT has ability to use the H.248.28/
international CAS package.
an Events Descriptor for the clear forward event with specific RequestID
was set using the international CAS package at the IUT for a specific
physical Termination (TID1) in the NULL Context. The IUT has detected
the seize event.
sends a Transaction Request containing:
Action request with
CID set to NULL
NOTIFY Command request with
TID set to TSPX_H248_28_TID1
ObservedEvents Descriptor
specific RequestID
observed event = icas/cf
international CAS package.
an Events Descriptor for the clear forward event with specific RequestID
was set using the international CAS package at the IUT for a specific
physical Termination (TID1) in the NULL Context. The IUT has detected
the seize event.
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.28
Text_Mode/
MG/
H248_28/
BI
Text_Mode/
MG/
H248_29
Text_Mode/
MG/
H248_29/
BV
H248_29_MG_TXT_BV_01 Initial condition: 2 Physical Terminations to make calls to and from
User Action: Dial phone number
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.16
Text_Mode/
MG/
H248_29/
BI
Text_Mode/
MG/
H248_28
Text_Mode/
MG/
H248_28/
BV
H248_34_MG_TXT_BV_01 Initial condition: SUT has ability to use the H.248.34 package
an Events Descriptor for the steady signal event with specific RequestID
and specific parameter detectsig set to "offHook" was set using
H.248.34 package at the IUT for a specific physical Termination (TID1)
in the NULL Context. The IUT has detected the off-hook event.
specific parameter detectsig set to "offHook"
sends a Transaction Request containing:
Action request with
CID set to NULL
NOTIFY Command request with
TID set to TSPX_H248_34_TID1
ObservedEvents Descriptor
specific RequestID
observed event = stimal/stedsig
parameter sig="offHook"
an Events Descriptor for the steady signal event with specific RequestID
and specific parameter detectsig set to "offHook" was set using
H.248.34 package at the IUT for a specific physical Termination (TID1)
in the NULL Context. The IUT has detected the off-hook event.
Config: Config1
SUT: MG
Status: Extension
Ref: H.246.34
Text_Mode/
MG/
H248_28/
BI
Text_Mode/
MGC
H248_MGC_TXT_Start_01 Sends a ServiceChangeReq; waits for response from the MGC
User Action: None
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2002-05 [1]
Text_Mode/
MGC/
H248_2
Text_Mode/
MGC/
H248_2/
BV
Text_Mode/
MGC/
H248_2/
BI
Text_Mode/
MGC/
H248_3
Text_Mode/
MGC/
H248_3/
BV
Text_Mode/
MGC/
H248_3/
BI
Text_Mode/
MGC/
H248_6
Text_Mode/
MGC/
H248_6/
BV
Text_Mode/
MGC/
H248_6/
BI
Text_Mode/
MGC/
H248_13
Text_Mode/
MGC/
H248_13/
BV
Text_Mode/
MGC/
H248_13/
BI
Text_Mode/
MGC/
H248_14
Text_Mode/
MGC/
H248_14/
BV
Text_Mode/
MGC/
H248_14/
BI
Text_Mode/
MGC/
H248_15
Text_Mode/
MGC/
H248_15/
BV
Text_Mode/
MGC/
H248_15/
BI
Text_Mode/
MGC/
H248_16
Text_Mode/
MGC/
H248_16/
BV
Text_Mode/
MGC/
H248_16/
BI
Text_Mode/
MGC/
H248_17
Text_Mode/
MGC/
H248_17/
BV
Text_Mode/
MGC/
H248_17/
BI
Text_Mode/
MGC/
H248_23
Text_Mode/
MGC/
H248_23/
BV
Text_Mode/
MGC/
H248_23/
BI
Text_Mode/
MGC/
H248_25
Text_Mode/
MGC/
H248_25/
BV
Text_Mode/
MGC/
H248_25/
BI
Text_Mode/
MGC/
H248_26
Text_Mode/
MGC/
H248_26/
BV
Text_Mode/
MGC/
H248_26/
BI

Variable Default Value Description
TSPX_MId_tester "192.168.1.57" Link 1. Can be one of the following : ip4Address ip6Address domainName deviceName mtpAddress
TSPX_MId_IUT "192.168.1.7" (null)
TSPX_MId_tester2 "192.168.1.62" Link 2. Can be one of the following : ip4Address ip6Address domainName deviceName mtpAddress
TSPX_MId_IUT2 "192.168.1.7" (null)
TSPX_KEEPALIVE_ON FALSE Set to TRUE if testing a TGW, FALSE for RGW
TSPX_KEEPALIVE_AUDIT_CONTENT "" When TSPX_KEEPALIVE_ON=TRUE, contains the content of the AuditValue Request(MG tests)/ Reply(MGC tests) message sent
TSPX_ServiceChangeAddress_Included FALSE Set to TRUE if including port in ServiceChangeAddress field, FALSE by default.
TSPX_TESTER_PORT 2944 DEFAULT is 2945 for BER AND 2944 text ENCODE
TSPX_TESTER_NEW_PORT 20001 Change to this in ServiceChangeReply if TGW_Mode TRUE
TSPX_SUT_PORT 2944 (null)
PX_Transport Transport_Param_UDP Transport used for Megaco
PX_TCP_Mode TCP_MGT_Server (null)
PX_Version_Number 2 1 = 1.0
PX_TerminationId_Root 'FFFFFFFFFFFFFFFF'H (null)
PX_Profile_Name "GW" (null)
PX_Media_Address "10.12.21.233" (null)
PX_Termid1 "line/1" (null)
PX_Profile "ResGW/1" (null)
SCTP_Mode FALSE (null)
N_Output_Streams 1 (null)
N_Input_Streams 1 (null)
PCO1_Adaptor_ID 1 (null)
N_Adaptors 1 (null)
N_Sockets 1 (null)
TSPX_TID_CHOOSE_EPH_text "$" Ephermeral Termination ID with CHOOSE wildcard for ephemeral (temporary) terminations
TSPX_TID_CHOOSE_PHY_text "$" Ephermeral Termination ID with CHOOSE wildcard for ephemeral (temporary) terminations
TSPX_TID1_text "line/1" Physical Termination ID (referenced as physical Termination TID1 in the TPs)
TSPX_TID2_text "line/2" Physical Termination ID (referenced as physical Termination TID2 in the TPs)
TSPX_TID3_text "line/3" Physical Termination ID (referenced as physical Termination TID3 in the TPs)
TSPX_TID4_text "line/4" Physical Termination ID (referenced as physical Termination TID4 in the TPs)
TSPX_TID_EPH_1_text "rtp/1" Ephemeral Termination ID 1 used in MGC tests
TSPX_TID_EPH_2_text "rtp/2" Ephemeral Termination ID 2 used in MGC tests
TSPX_TID_EPH_3_text "rtp/3" Ephemeral Termination ID 3 used in MGC tests
TSPX_TID_EPH_4_text "rtp/4" Ephemeral Termination ID 4 used in MGC tests
TSPX_TID_ALL_EPH_text "*" Termination ID with ALL wildcard which addresses ephemeral Terminations TID1 and TID2
TSPX_TID_ALL_PHY_2_C1 "line/*" Termination ID with ALL wildcard which addresses physical Terminations TID1 and TID2
TSPX_TID_ALL_PHY_2_C2 "line/*" Termination ID with ALL wildcard which addresses physical Terminations TID3 and TID4
TSPX_TID_ALL_PHY_2_text "line/*" Termination ID with ALL wildcard which addresses 2 physical Terminations TID1 and TID2
TSPX_H248_8_Unknown_TID "unknown/1" An unknown Termination ID used to test extension H248.8 error code 430.
TSPX_H248_25_TID1 "line/1" Termination ID used in test H248_25_MG_TXT_BV_01 for extension H248.25
TSPX_H248_26_TID1 "line/1" Termination ID used in test H248_26_MG_TXT_BV_01 for extension H248.26
TSPX_H248_28_TID1 "line/1" Termination ID used in test H248_28_MG_TXT_BV_01 for extension H248.28
TSPX_H248_29_TID1 "line/1" Termination ID used in tests for extension H248.29
TSPX_H248_34_TID1 "line/1" Termination ID used in test H248_34_MG_TXT_BV_01 for extension H248.34
TCV_Audit_text "Events,Mux" Audit descriptors to use in the tests.
TCV_Audit_Root_text "Statistics" Audit descriptors for Root Terminations
TCV_Request_ID "1234" The Request ID for the Events Descriptor
TCV_Events_Desc "al/of" All the Events Descriptor in proper text format
TSPX_EVENTS_DESC_EPH "al/of" All the Events Descriptor in proper text format
TSPX_OBSERVED_EVENTS_DESC_EPH_TXT "al/of" The event(s) to generate in MGC tests, for Notify tests for ephemeral terminations.
TSPX_OBSERVED_EVENTS_DESC_PHY_TXT "al/of" The event(s) to generate in MGC tests, for Notify tests for physical terminations.
TSPX_OBSERVED_EVENTS_DESC_ROOT_TXT "al/of" The event(s) to generate in MGC tests, for Notify tests for ROOT terminations.
TCV_Signals_Desc "al/ri" All the Signals Descriptor in proper text format
TSC_SCDtime "2" The ServiceChange Delay time
TCV_SCMgcId "[192.1.168.62]:2944" (null)
TCV_Notify_StreamID "1" The stream ID of the event the Notify is indicating
TSPX_LONG_TIMER 60000 The LONG_TIMER indicating how many secs before resending a reply message.
TSPX_NormalMGCExecutionTime 30000 The time which indicates the interval that the MG expects a response from the MGC.
TSPX_Max_InActivity_Time "5000" The Maximum Inactivity Time, in millisecs
TSPX_NEW_TONEID "0x0050" The tone ID, ts1,(0x0050) of the new tone to create using dynamic tone definition package
TSPX_EXIST_TONEID "0x0031" The existing tone ID to edit using dynamic tone definition package
TSPX_TONE_STRING "((0x1122,0x0050),((#400)+(#50... The new tone string
TSPX_EDITED_TONE_STRING "((0x0005,0x0031),((#480)+(#62... The edited tone string
TSPX_INVALID_TONE_STRING "0x1122,0x0050),#400)+(#500)),... The invalid tone string
TSPX_QUAL_ALERT_TH "10" The percentage of quality loss measured to generate a qualert event
TSPX_QUAL_ALERT_CEASE_TH "8" The percentage of quality loss measured to generate a qualertcease event
TSPX_Package_Property_Name "nt/jit" The percentage of quality loss measured to generate a qualertcease event
TSPX_Package_Property_Value "2000" The percentage of quality loss measured to generate a qualertcease event
USER_LCDM1_TOKEN_TXT "" Custom Amm parameter
USER_LCDM1_VALUE_TXT "" Custom Amm parameter
USER_LCDPP1_NAME1_TXT "" Custom Amm parameter
USER_LCDPP1_VALUE1_TXT "" Custom Amm parameter
USER_LDN1_NAME1_TXT "" Custom Amm parameter
USER_LDN1_VALUE1_TXT "" Custom Amm parameter
USER_LDN1_NAME2_TXT "" Custom Amm parameter
USER_LDN1_VALUE2_TXT "" Custom Amm parameter
USER_LDN1_NAME3_TXT "" Custom Amm parameter
USER_LDN1_VALUE3_TXT "" Custom Amm parameter
USER_LDN1_NAME4_TXT "" Custom Amm parameter
USER_LDN1_VALUE4_TXT "" Custom Amm parameter
USER_LCDM2_TOKEN_TXT "" Custom Amm parameter
USER_LCDM2_VALUE_TXT "" Custom Amm parameter
USER_LCDPP2_NAME1_TXT "" Custom Amm parameter
USER_LCDPP2_VALUE1_TXT "" Custom Amm parameter
USER_TID1_TXT "" Custom Amm parameter
PCO1_Use_Primary_Address TRUE Use primary or secondary NIC card for this PCO
PCO2_Use_Primary_Address TRUE Use primary or secondary NIC card for this PCO
PCO3_Use_Primary_Address TRUE Use primary or secondary NIC card for this PCO
PCO4_Use_Primary_Address TRUE Use primary or secondary NIC card for this PCO
PCO2_2_Src_IP_Addr "192.168.5.47" (null)
PCO2_2_Dst_IP_Addr "192.168.5.58" (null)
PCO2_2_Src_Port 9900 (null)
PCO2_2_Dst_Port 9900 (null)
Layer_3_Protocol Use_IPv4 Network layer; above Ethernet, default = Use_IPv4
PCO1_Src_IPv6_Addr '00010000000000000000000000000... (null)
PCO1_Dst_IPv6_Addr '00020000000000000000000000000... (null)
TSPX_TID_ALL 'FFFFFFFF'H Termination ID with NULL wildcard for both, ephemeral and physical Terminations
TSPX_TID_ALL_EPH 'FFFFFFFF'H Termination ID with NULL wildcard for both, ephemeral and physical Terminations
TSPX_AV_AUDIT_DESC_ROOT 'FFFFFFFFFFFFFFFF'H (null)
TSPX_AV_AUDIT_DESC_EPH 'FFFFFFFFFFFFFFFF'H (null)
TSPX_TID_CHOOSE_PHY 'FFFFFFFFFFFFFFFF'H (null)
TSPX_TID_CHOOSE_EPH 'FFFFFFFE'H Ephermeral Termination ID with CHOOSE wildcard for ephemeral (temporary) terminations
TSPX_TID1 '00000001'H Physical Termination ID (referenced as physical Termination TID1 in the TPs)
TSPX_TID2 '00000002'H Physical Termination ID (referenced as physical Termination TID2 in the TPs)
TSPX_TID3 '00000003'H Physical Termination ID (referenced as physical Termination TID3 in the TPs)
TSPX_TID4 '00000004'H Physical Termination ID (referenced as physical Termination TID4 in the TPs)
TSC_TID_ROOT 'FFFFFFFFFFFFFFFF'H (null)
Ip_Address (null) 1 = 1.0
Ip_Port 55555 (null)
Event_Request_ID '5555'H (null)
Mgc_Termination_Id "a4444" first modify request id
Termination_1 (null) (null)
Termination_2 (null) (null)
T_Active_VAL 5000 (null)

Copyright © ACATS Forum 2008 on behalf of the test suite author. All rights reserved. Specifications may change subject to requirements.

01 Apr 2009 Produced by SAFIRE V20.05.14.01
www.SAFIRE-World.com		 Test Suite Overview