Valid8.com/ACATS VoIP Megaco/H.248 Conformance Test Suite for MGC/MG and PGC/PG testing, for use with H.248 Megaco Signaling Tester
TEST SUITE OVERVIEW
References ETSI TS 102-374-2 2004/11 text mode) / IETF Megaco RFC3525, ITU-T H.248.1v3
Archive/Project voip/Megaco_TS
Version 19171599
Date 08 Dec 2008
Number of Scenarios 370
Number of Groups 47
Average per Group 7
GROUP/SCENARIO TEST PURPOSE
Text_Mode
Text_Mode/
MG
H248_MG_TXT_Start_01 Wait for ServiceChangeReq, send response, est. connection
the tester and the SUT.
Initial condition: any
User Action: Generate a Service Change event, "Cold Reboot"
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1]
H248_MG_TXT_Start_02 Wait for ServiceChangeReq, send response, est. connection
the tester and the SUT. Send Modify(s) / Audit(s).
Initial condition: any
User Action: Generate a Service Change event, "Cold Reboot"
Config: Config1
SUT: AMG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1]
Text_Mode/
MG/
AD
Text_Mode/
MG/
AD/
BV
H248_MG_TXT_AD_BV_01 Init: any. Test: Sends Transaction Rq ADD, CID=CHOOSE, TID=CHOOSE

Initial condition: any
Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
ADD Command request with
TID set to CHOOSE
acceptable descriptors (note: e.g. for creation of
a RTP Termination)
sends a Transaction reply containing
Action reply with
CID set to a specific value (assigned by the MG)
ADD Command reply with
TID set to a specific value (assigned by the MG).
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BV_02 Init: 1 phy term=TID1 & not outOfService in CID=NULL. Test: Sends Transaction Rq ADD, CID=CHOOSE, TID=TID1
The physical Termination TID1 shall NOT be in serviceState "outOfService".
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
ADD Command request with
TID set to TID1
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to a specific value (assigned by the MG)
ADD Command reply with
TID set to TID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BV_03 Init: 2 phy term=TID1,TID2 & not outOfService in CID=NULL. Test: Sends Transaction Rq ADD, CID=CHOOSE, TID=ALL
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
ADD Command request with
TID set to ALL(p12)
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to a specific value (assigned by the MG)
ADD Command reply with
TID set to TID1
ADD Command
TID set to TID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BV_04 Init: 1 eph term=TID1 in CID=CID1. Test: Sends Transaction Rq ADD, CID=CID1, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
ADD Command request with
TID set to CHOOSE
acceptable descriptors
(note: e.g. for creation of a RTP Termination)
sends a Transaction Reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to a specific value (assigned by the MG).
Initial condition: a Termination characterized by TID1 in a Context, characterized by CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BV_05 Init: 2 phy term=TID1,TID2 & not outOfService in CID=NULL, 1 eph term=TID3 in CID=CID1, Test: Sends Transaction Rq ADD, CID=CID1, TID=ALL
The physical Terminations TID1 and TID2 shall NOT be in serviceState "outOfService".
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
ADD Command request with
TID set to ALL(p12)
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to TID1
ADD Command reply with
TID set to TID2.
The physical Terminations TID1 and TID2 shall NOT be in serviceState "outOfService".
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BV_06 Init: 1 phy term=TID2 & not outOfService in CID=NULL, 1 eph term=TID1 in CID=CID1. Test: Sends Transaction Rq Add, CID=CID1, TID=TID2
Initial condition: A physical Termination, characterized by TID2, in the NULL Context and
a Termination (TID1) in Context CID1. The terminations TID1 and TID2 shall
NOT be in serviceState, "outOfService".
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
ADD Command request with
TID set to TID2
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to TID2

a Termination (TID1) in Context CID1. The terminations TID1 and TID2 shall
NOT be in serviceState, "outOfService".
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BV_07 Init: 2 eph term=TID1,TID2 in CID=CID1,CID2 (not NULL CID). Test: Sends Transaction Rq Add, CID=ALL, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
ADD Command request with
TID set to CHOOSE
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to TID3
Action reply with
CID set to CID2
ADD Command reply with
TID set to TID4
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
Text_Mode/
MG/
AD/
BI
H248_MG_TXT_AD_BI_01 Init: any. Test: Send Transaction Rq ADD, CID=CHOOSE, TID=ROOT
Initial condition: any
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
ADD Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
ADD Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.1 and 6.2.5
H248_MG_TXT_AD_BI_02 Init: 1 eph term=TID1 in CID=CID1. Test: Send Transaction Rq ADD, CID=CID1, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
ADD Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")

Initial condition: a Termination (TID1) in a Context, characterized by CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.1 and 6.2.5
H248_MG_TXT_AD_BI_03 Init: 2 eph term=TID1,TID2 in CID=CID1,CID2 (not NULL CID). Test: Send Transaction Rq ADD, CID=ALL, TID=ALL
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
ADD Command request with
TID set to ALL
sends a Transaction Reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to TID1
Error descriptor (value 433 "TerminationID is already in a Context")

Action reply with
CID set to CID2
ADD Command reply with
TID set to TID2
Error descriptor (value 433 "TerminationID is already in a Context")

Initial condition: 2 Terminations (TID1 and TID2) each in a Context, characterized by CID1 and CID2 (NULL Context is excluded).
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BI_04 Init: 2 eph term=TID1,TID2 in CID=CID1,CID2 (not NULL CID). Test: Send Transaction Rq ADD, CID=ALL, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
ADD Command request with
TID set to a specific TID (e.g. TID1),
sends a Transaction Reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to TID1
Error descriptor (value 433 "TerminationID is already in a Context")
Initial condition: 2 Terminations (TID1 and TID2) each in a Context, characterized by CID1 and CID2 (NULL Context is excluded).
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BI_05 Init: 2 eph term TID1,TID2 in CID=CID1,CID2 (not NULL CID). Test: Send Transaction Rq ADD, CID=ALL, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
ADD Command request with
TID set to ROOT,
sends a Transaction Reply containing
Action reply with
CID set to ALL
ADD Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")
Initial condition: 2 Terminations (TID1 and TID2) each in a Context, characterized by CID1 and CID2 (NULL Context is excluded).
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.1 and 6.2.5
H248_MG_TXT_AD_BI_06 Init: 2 phy term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq ADD, CID=NULL, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
ADD Command request with
TID set to a specific TID1
sends a Transaction Reply containing
Action reply with
CID set to NULL
ADD Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol Error")

Initial condition: 2 physical Terminations in the NULL Context, characterized by TID1 and TID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BI_07 Init: 2 phy term TID1,TID2 in CID=NULL. Test: Send Transaction Rq ADD, CID=NULL, TID=ALL
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
ADD Command request with
TID set to ALL
sends a Transaction Reply containing
Action reply with
CID set to NULL
ADD Command reply with
TID set to ALL
Error descriptor (e.g. value 401 "Protocol Error")

Initial condition: 2 physical Terminations in the NULL Context, characterized by TID1 and TID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BI_08 Init: 2 phy term TID1,TID2 in CID=NULL. Test: Send Transaction Rq ADD, CID=NULL, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
ADD Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to NULL
ADD Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
Initial condition: 2 physical Terminations in the NULL Context, characterized by TID1 and TID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MG_TXT_AD_BI_09 Init: 2 phy term TID1,TID2 in CID=NULL. Test: Send Transaction Rq ADD, CID=NULL, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
ADD Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to NULL
ADD Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")

Initial condition: 2 physical Terminations in the NULL Context, characterized by TID1 and TID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.1 and 6.2.5
Text_Mode/
MG/
MD
Text_Mode/
MG/
MD/
BV
H248_MG_TXT_MD_BV_01 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Sends Transaction Rq Modify, CID=CID1, TID=ALL
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
MODIFY Command request with
TID set to ALL(e12)
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to TID1
MODIFY Command reply with
TID set to TID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BV_02 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Modify, CID=CID1, TID=TID1
Initial condition: 2 Terminations, characterized by TID1 and TID2 within Context CID1.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
MODIFY Command request with
TID set to TID1,
sends a Transaction Reply containing
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to TID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BV_03 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Modify, CID=ALL, TID=ALL(e1234)
Initial condition: 2 Terminations characterized by TID1 and TID2 within Context CID1;
2 Terminations characterized by TID3 and TID4 within Context CID2.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
MODIFY Command request with
TID set to ALL(e1234)
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to TID1
MODIFY Command reply with
TID set to TID2
Action reply with
CID set to CID2
MODIFY Command reply with
TID set to TID3
MODIFY Command reply with
TID set to TID4.
2 Terminations characterized by TID3 and TID4 within Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BV_04 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Modify, CID=ALL, TID=TID3
Initial condition: 2 Terminations characterized by TID1 and TID2 within Context CID1;
2 Terminations characterized by TID3 and TID4 within Context CID2.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
MODIFY Command request with
TID set to TID3
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to CID2
MODIFY Command reply with
TID set to TID3
2 Terminations characterized by TID3 and TID4 within Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BV_05 Init: 2 eph term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Modify, CID=NULL, TID=ALL(p12)
Initial condition: 2 physical Terminations (TID1 and TID2) in the NULL Context.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
MODIFY Command request with
TID set to ALL(p12)
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to NULL
MODIFY Command reply with
TID set to TID1
MODIFY Command reply with
TID set to TID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BV_06 Init: 1 phy term=TID1 in CID=NULL. Test: Send Transaction Rq Modify, CID=NULL, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
MODIFY Command request with
TID set to TID1
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to NULL
MODIFY Command reply with
TID set to TID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BV_07 Init: any. Test: Send Transaction Rq Modify, CID=NULL, TID=ROOT
Initial condition: any
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
MODIFY Command request with
TID set to ROOT
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to NULL
MODIFY Command reply with
TID set to ROOT.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
Text_Mode/
MG/
MD/
BI
H248_MG_TXT_MD_BI_01 Init: any. Test: Send Transaction Rq Modify, CID=CHOOSE, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
MODIFY Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
MODIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error"
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BI_02 Init: 2 eph term=TID1,TID2 in a CID, Test: Send Transaction Rq Modify, CID=CHOOSE, TID=ALL
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
MODIFY Command request with
TID set to ALL
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
MODIFY Command reply with
TID set to ALL
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BI_03 Init: any. Test: Send Transaction Rq Modify, CID=CHOOSE, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
MODIFY Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
MODIFY Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.2 and 6.2.5
H248_MG_TXT_MD_BI_04 Init: Existing CID=CID1. Test: Send Transaction Rq Modify, CID=CID1, TID=CHOOSE
Initial condition: an existing Context, characterized by CID1.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
MODIFY Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BI_05 Init: Existing CID=CID1. Test: Send Transaction Rq Modify, CID=CID1, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
MODIFY Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to ROOT
Error descriptor (value 410 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.2 and 6.2.5
H248_MG_TXT_MD_BI_06 Init: 2 eph term=TID1,TID2 in CID=CID1,CID2. Test: Send Transaction Rq Modify, CID=ALL, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
MODIFY Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to ALL
MODIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BI_07 Init: 2 eph term=TID1,TID2 in CID=CID1,CID2. Test: Send Transaction Rq Modify, CID=ALL, TID=ROOT
Initial condition: 2 existing Contexts, characterized by CID1 and CID2 and 2 Terminations characterized by TID1 and TID2 within the Contexts.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
MODIFY Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to ALL
MODIFY Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.2 and 6.2.5
H248_MG_TXT_MD_BI_08 Init: 2 phy term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Modify, CID=NULL, TID=CHOOSE
Initial condition: 2 physical Terminations, characterized by TID1 and TID2, in the NULL Context.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
MODIFY Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to NULL
MODIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
H248_MG_TXT_MD_BI_09 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Modify, CID=CHOOSE, TID=TID1
Initial condition: 2 Terminations (TID1 and TID2) exist in a Context CID1.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
MODIFY Command request with
TID set to TID1
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
MODIFY Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.2
Text_Mode/
MG/
SU
Text_Mode/
MG/
SU/
BV
H248_MG_TXT_SU_BV_01 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Subtract, CID=CID1, TID=ALL(e12), Audit Descriptor=empty
Initial condition: 2 Terminations (TID1 and TID2) within a Context CID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to ALL(e12)
empty Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to TID1
SUBTRACT Command reply with
TID set to TID2.

Initial condition: 2 Terminations (TID1 and TID2) within a Context CID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BV_02 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Subtract, CID=CID1, TID=ALL(e12), wildcardReturn Rq, Audit Descriptor=empty
Selection criteria: wildcardReturn request procedure implemented.
Initial condition: 2 Terminations (TID1 and TID2) within a Context CID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to ALL(e12)
wildcardReturn request
empty Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to ALL(e12)
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BV_03 Init: 1 eph term=TID1 in CID=CID1. Test: Send Transaction Rq Subtract, CID=CID1, TID=TID1, Audit Descriptor=empty
Initial condition: one Termination characterized by TID1 is in a Context, characterized by CID1.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to TID1
empty Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to TID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BV_04 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Subtract, CID=ALL, TID=ALL(e1234), Audit Descriptor=empty, wildcardReturn request
Selection criteria: wildcardReturn request procedure implemented
Initial condition: 2 Terminations (TID1 and TID2) are in a Context CID1 and 2 Terminations (TID3 and TID4) are in a Context CID2.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to ALL(e1234)
empty Audit Descriptor
wildcardReturn request
sends a Transaction Reply containing
Action reply with
CID set to ALL
SUBTRACT Command reply with
TID set to ALL(e1234)
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
12.2.2 [1]
H248_MG_TXT_SU_BV_05 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Subtract, CID=ALL, TID=ALL(e1234), Audit Descriptor=empty
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to ALL(e1234)
empty Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to TID1
SUBTRACT Command reply with
TID set to TID2
Action reply with
CID set to CID2
SUBTRACT Command reply with
TID set to TID3
SUBTRACT Command reply with
TID set to TID4.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BV_06 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Subtract, CID=ALL, TID=TID3, Audit Descriptor= empty
Initial condition: 2 Terminations (TID1 and TID2) are in a Context CID1 and 2 Terminations (TID3 and TID4) are in a Context CID2.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to TID3
empty Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID2
SUBTRACT Command reply with
TID set to TID3
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
Text_Mode/
MG/
SU/
BI
H248_MG_TXT_SU_BI_01 Init: any. Test: Send Transaction Rq Subtract, CID=CHOOSE, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BI_02 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Subtract, CID=CHOOSE, TID=ALL(e12)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
SUBTRACT Command request with
TID set to ALL(e12)
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
SUBTRACT Command reply with
TID set to ALL
Error descriptor (e.g. value 401 "Protocol Error")

Initial condition: 2 Terminations (TID1 and TID2) in Context CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BI_03 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Subtract, CID=CHOOSE, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
SUBTRACT Command request with
TID set to TID1
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
SUBTRACT Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol Error")

Initial condition: 2 Terminations (TID1 and TID2) in Context CID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BI_04 Init:any. Test: Send Transaction Rq Subtract, CID=CHOOSE, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
SUBTRACT Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.3 and 6.2.5
H248_MG_TXT_SU_BI_05 Init: 1 eph term=TID1 in CID=CID1. Test: Send Transaction Rq Subtract, CID=CID1, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BI_06 Init: 1 eph term=TID1 in CID=CID1. Test: Send Transaction Rq Subtract, CID=CID1, TID=ROOT
Initial condition: a Termination characterized by TID1 in a Context, characterized by CID1.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.3 and 6.2.5
H248_MG_TXT_SU_BI_07 Init: 2 eph term=TID1 in CID=CID1,CID2. Test: Send Transaction Rq Subtract, CID=ALL, TID=CHOOSE
and Terminations characterized by TID1 and TD2 within the Contexts.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to ALL
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")

Initial condition: 2 existing Contexts, characterized by CID1 and CID2
and Terminations characterized by TID1 and TD2 within the Contexts.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BI_08 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 ePh term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Subtract, CID=ALL, TID=ROOT
Initial condition: 2 Terminations (TID1 and TID2) are in Context CID1, 2 Termination (TID3, TID4) are in Context CID2.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to ALL
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.3 and 6.2.5
H248_MG_TXT_SU_BI_09 Init: 2 phys term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Subtract, CID=NULL, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BI_10 Init: 2 phys term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Subtract, CID=NULL, TID=ALL(p12)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to ALL(p12)
sends a Transaction Reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to ALL (p12)
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BI_11 Init: 2 phys term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Subtract, CID=NULL, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to TID1
sends a Transaction Reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol Error")

Initial condition: 2 physical Terminations (TID1 and TID2) exist in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.3
H248_MG_TXT_SU_BI_12 Init: 2 Phys term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Subtract, CID=NULL, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")

Initial condition: 2 physical Terminations (TID1 and TID2) exist in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.3 and 6.2.5
Text_Mode/
MG/
MO
Text_Mode/
MG/
MO/
BV
H248_MG_TXT_MO_BV_01 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Move, CID=CID2, TID=ALL(e12)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID2
MOVE Command request with
TID set to ALL(e12)
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to CID2
MOVE Command reply with
TID set to TID1
MOVE Command reply with
TID set to TID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
H248_MG_TXT_MO_BV_02 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Move, CID=CID2, TID=TID2
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID2
MOVE Command request with
TID set to TID2
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to CID2
MOVE Command reply with
TID set to TID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
H248_MG_TXT_MO_BV_03 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Move, CID=CHOOSE, TID=ALL(e12)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
MOVE Command request with
TID set to ALL(e12)
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to CID2 (assigned by MG, CID1 is deleted by the MG)
MOVE Command reply with
TID set to TID1
MOVE Command reply with
TID set to TID2
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
H248_MG_TXT_MO_BV_04 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Move, CID=CHOOSE, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
MOVE Command request with
TID set to TID1
acceptable descriptors
sends a Transaction Reply containing
Action reply with
CID set to CID2 (assigned by the MG)
MOVE Command reply with
TID set to TID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
Text_Mode/
MG/
MO/
BI
H248_MG_TXT_MO_BI_01 Init: any. Test: Send Transaction Rq Move, CID=CHOOSE, TID=CHOOSE
Action request with
CID set to CHOOSE
MOVE Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
MOVE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")

Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
H248_MG_TXT_MO_BI_02 Init: any. Test: Send Transaction Rq Move, CID=CHOOSE, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
MOVE Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
MOVE Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.4 and 6.2.5
H248_MG_TXT_MO_BI_03 Init: 1 eph term=TID1 in CID=CID1. Test: Send Transaction Rq Move, CID=CID1, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
MOVE Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to CID1
MOVE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
H248_MG_TXT_MO_BI_04 Init: 1 eph term=TID1 in CID=CID1. Test: Send Transaction Rq Move, CID=CID1, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
MOVE Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to CID1
MOVE Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.4 and 6.2.5
H248_MG_TXT_MO_BI_05 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Move, CID=ALL, TID=ALL(e1234)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
MOVE Command request with
TID set to ALL(e1234)
sends a Transaction Reply containing
Action reply with
CID set to ALL
MOVE Command reply with
TID set to ALL(e1234)
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
H248_MG_TXT_MO_BI_06 Init: 2 phys term=TID1,TID2 in CID=CID1, 2 phys term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Move, CID=ALL, TID=CHOOSE
Initial condition: 2 physical Terminations (TID1 and TID2) in Context CID1, 2 physical Termination (TID3, TID4) in Context CID2.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
MOVE Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to ALL
MOVE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
H248_MG_TXT_MO_BI_07 Init: 2 phys term=TID1,TID2 in CID=CID1, 2 phys term=TID3,TID4 in CID=CID2. Test: Rx Transaction Rq Move, CID=ALL, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
MOVE Command request with
TID set to TID1
sends a Transaction Reply containing
Action reply with
CID set to ALL
MOVE Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
H248_MG_TXT_MO_BI_08 Init: 2 phys term=TID1,TID2 in CID=CID1, 2 phys term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Move, CID=ALL, TID=ROOT
Selection criteria: ROOT Termination implemented
Initial condition: 2 physical Terminations (TID1 and TID2) in Context CID1, 2 physical Termination (TID3, TID4) in Context CID2.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
MOVE Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to ALL
MOVE Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.4 and 6.2.5
H248_MG_TXT_MO_BI_09 Init: 2 phys term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Move, CID=NULL, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
MOVE Command request with
TID set to CHOOSE
sends a Transaction Reply containing
Action reply with
CID set to NULL
MOVE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")

Initial condition: 2 physical Terminations (TID1 and TID2) in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
H248_MG_TXT_MO_BI_10 Init: 2 phys term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Move, CID=NULL, TID=ROOT
Initial condition: 2 physical Terminations (TID1 and TID2) in the NULL Context.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
MOVE Command request with
TID set to ROOT
sends a Transaction Reply containing
Action reply with
CID set to NULL
MOVE Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.4 and 6.2.5
H248_MG_TXT_MO_BI_11 Init: 2 phys term=TID1,TID2 in CID=CID1, 2 phys term=TID3,TID4 in CID=CID2. Test:Send Transaction Rq Move, CID=NULL, TID=ALL(p12)
Initial condition: 2 physical Terminations (TID1 and TID2) in Context CID1, 2 physical Terminations (TID3 and TID4) in Context CID2
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
MOVE Command request with
TID set to ALL(p12)
sends a Transaction Reply containing
Action reply with
CID set to NULL
MOVE Command reply with
TID set to ALL(p12)
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
H248_MG_TXT_MO_BI_12 Init: 2 phys term=TID1,TID2 in CID=CID1, 2 phys term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Move, CID=NULL, TID=TID1
Initial condition: 2 physical Terminations (TID1 and TID2) in Context CID1, 2 physical Terminations (TID3 and TID4) in Context CID2
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
MOVE Command request with
TID set to TID1
sends a Transaction Reply containing
Action reply with
CID set to NULL
MOVE Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.4
Text_Mode/
MG/
AV
Text_Mode/
MG/
AV/
BV
H248_MG_TXT_AV_BV_01 Init: 2 eph term=TID1,TID2 in CID=CID1, Rx Transaction Rq Audit Value, CID=CID1, TID=ALL(e12)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
AUDIT VALUE Command request with
TID set to ALL(e12)
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT VALUE Command reply with
TID set to TID1
AUDIT VALUE Command reply with
TID set to TID2
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BV_02 Init: 2 eph term=TID1,TID2 in CID1. Test: Send Transaction Rq Audit Value, CID=CID1, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
AUDIT VALUE Command request with
TID set to TID1
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT VALUE Command reply with
TID set to TID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BV_03 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Audit Value, CID=ALL, TID=ALL(e23)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
AUDIT VALUE Command request with
TID set to ALL(e23)
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT VALUE Command reply with
TID set to TID2
Action reply with
CID set to CID2
AUDIT VALUE Command reply with
TID set to TID3
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BV_04 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Audit Value, CID=ALL, TID=TID1
2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
AUDIT VALUE Command request with
TID set to TID1
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT VALUE Command reply with
TID set to TID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BV_05 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Request Audit Value, CID=ALL, TID=ROOT
2 Terminations (TID3, TID4) in Context CID2.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
AUDIT VALUE Command request with
TID set to ROOT
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
with an empty list of commands
Action reply with
CID set to CID2
with an empty list of commands
2 Terminations (TID3, TID4) in Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BV_06 Init: 2 phys term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Audit Value, CID=NULL, TID=ALL(p12)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
AUDIT VALUE Command request with
TID set to ALL(p12)
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to NULL
AUDIT VALUE Command reply with
TID set to TID1
AUDIT VALUE Command reply with
TID set to TID2

Initial condition: 2 physical Terminations (TID1, TID2) in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BV_07 Init: 2 phys term=TID1,TID2 in CID=NULL. Actions: Send Transaction Rq Audit Value, CID=NULL, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
AUDIT VALUE Command request with
TID set to TID1
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to NULL
AUDIT VALUE Command reply with
TID set to TID1

Initial condition: 2 physical Terminations (TID1, TID2) in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BV_08 Init: any. Test: Send Transaction Rq Audit Value, CID=NULL, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
AUDIT VALUE Command request with
TID set to ROOT
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to NULL
AUDIT VALUE Command reply with
TID set to ROOT
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
Text_Mode/
MG/
AV/
BI
H248_MG_TXT_AV_BI_01 Init: any. Test: Send Transaction Rq Audit Value, CID=CHOOSE, TID=CHOOSE
Action request with
CID set to CHOOSE
AUDIT VALUE Command request with
TID set to CHOOSE
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
AUDIT VALUE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BI_02 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Audit Value, CID=CHOOSE, TID=ALL(e12)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
AUDIT VALUE Command request with
TID set to ALL(e12)
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
AUDIT VALUE Command reply with
TID set to ALL(e12)
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BI_03 Init: 2 eph term=TID1 in CID=CID1. Test: Send Transaction Rq Audit Value, CID=CHOOSE, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
AUDIT VALUE Command request with
TID set to TID1
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
AUDIT VALUE Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BI_04 Init:any. Test: Send Transaction Rq Audit Value, CID=CHOOSE, TID=ROOT
Action request with
CID set to CHOOSE
AUDIT VALUE Command request with
TID set to ROOT
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
AUDIT VALUE Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.5 and 6.2.5
H248_MG_TXT_AV_BI_05 Init: 1 eph term=TID1 in CID=CID1. Test: Send Transaction Rq Audit Value, CID=CID1, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
AUDIT VALUE Command request with
TID set to CHOOSE
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT VALUE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BI_06 Init: 1 eph term=TID1 in CID=CID1. Test: Send Transaction Rq Audit Value, CID=CID1, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
AUDIT VALUE Command request with
TID set to ROOT
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT VALUE Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.5 and 6.2.5
H248_MG_TXT_AV_BI_07 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Audit Value, CID=ALL, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
AUDIT VALUE Command request with
TID set to CHOOSE
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to ALL
AUDIT VALUE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AV_BI_08 Init: 2 eph term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Audit Value, CID=NULL, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
AUDIT VALUE Command request with
TID set to CHOOSE
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to NULL
AUDIT VALUE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
Text_Mode/
MG/
AC
Text_Mode/
MG/
AC/
BV
H248_MG_TXT_AC_BV_01 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Audit Cap, CID=CID1, TID=ALL(e12)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
AUDIT CAPABILITIES Command request with
TID set to ALL(e12)
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT CAPABILITIES Command reply with
TID set to TID1
AUDIT CAPABILITIES Command reply with
TID set to TID2
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BV_02 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Audit Cap, CID=CID1, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
AUDIT CAPABILITIES Command request with
TID set to TID1
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT CAPABILITIES Command reply with
TID set to TID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BV_03 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Audit Cap, CID=ALL, TID=ALL(e1234)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
AUDIT CAPABILITIES Command request with
TID set to ALL(e1234)
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT CAPABILITIES Command reply with
TID set to TID1
AUDIT CAPABILITIES Command reply with
TID set to TID2
Action reply with
CID set to CID2
AUDIT CAPABILITIES Command reply with
TID set to TID3
AUDIT CAPABILITIES Command reply with
TID set to TID4.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BV_04 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Audit Cap, CID=ALL, TID=TID1
2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
AUDIT CAPABILITIES Command request with
TID set to TID1
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT CAPABILITIES Command reply with
TID set to TID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BV_05 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Audit Cap, CID=ALL, TID=ROOT
2 Terminations (TID3, TID4) in Context CID2.
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
AUDIT CAPABILITIES Command request with
TID set to ROOT
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
with an empty list of commands
Action reply with
CID set to CID2
with an empty list of commands
2 Terminations (TID3, TID4) in Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BV_06 Init: 2 phys term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Audit Cap, CID=NULL, TID=ALL(p12)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
AUDIT CAPABILITIES Command request with
TID set to ALL(p12)
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to NULL
AUDIT CAPABILITIES Command reply with
TID set to TID1
AUDIT CAPABILITIES Command reply with
TID set to TID2
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BV_07 Init: 2 phys term=TID1,TID2 in CID=NULL. Test: Send Transaction Rq Audit Cap, CID=NULL, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
AUDIT CAPABILITIES Command request with
TID set to TID1
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to NULL
AUDIT CAPABILITIES Command reply with
TID set to TID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BV_08 Init: any. Test: Send Transaction Rq Audit Cap, CID=NULL, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
AUDIT CAPABILITIES Command request with
TID set to ROOT
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to NULL
AUDIT CAPABILITIES Command reply with
TID set to ROOT
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
Text_Mode/
MG/
AC/
BI
H248_MG_TXT_AC_BI_01 Init: any. Test: Send Transaction Rq Audit Cap, CID=CHOOSE, TID=CHOOSE
Action request with
CID set to CHOOSE
AUDIT CAPABILITIES Command request with
TID set to CHOOSE
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
AUDIT CAPABILITIES Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BI_02 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Audit Cap, CID=CHOOSE, TID=ALL(e12)
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
AUDIT CAPABILITIES Command request with
TID set to ALL(e12)
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
AUDIT CAPABILITIES Command reply with
TID set to ALL(e12)
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BI_03 Init: 2 eph term=TID1,TID2 in CID=CID1. Test: Send Transaction Rq Audit Cap, CID=CHOOSE, TID=TID1
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CHOOSE
AUDIT CAPABILITIES Command request with
TID set to TID1
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
AUDIT CAPABILITIES Command reply with
TID set to TID1
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BI_04 Init: any. Test: Send Transaction Rq Audit Cap, CID=CHOOSE, TID=ROOT
Action request with
CID set to CHOOSE
AUDIT CAPABILITIES Command request with
TID set to ROOT
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CHOOSE
AUDIT CAPABILITIES Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.5 and 6.2.5
H248_MG_TXT_AC_BI_05 Init: 1 eph term=TID1 in CID=CID1. Test: Send Transaction Rq Audit Cap, CID=CID1, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
AUDIT CAPABILITIES Command request with
TID set to CHOOSE
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT CAPABILITIES Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BI_06 Init: 1 eph term=TID1 in CID=CID1. Test: Send Transaction Rq Audit Cap, CID=CID1, TID=ROOT
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to CID1
AUDIT CAPABILITIES Command request with
TID set to ROOT
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to CID1
AUDIT CAPABILITIES Command reply with
TID set to ROOT
Error descriptor (value 410 "Incorrect Identifier")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clauses 7.2.5 and 6.2.5
H248_MG_TXT_AC_BI_07 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Audit Cap, CID=ALL, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
AUDIT CAPABILITIES Command request with
TID set to CHOOSE
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to ALL
AUDIT CAPABILITIES Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
H248_MG_TXT_AC_BI_08 Init: 2 eph term=TID1,TID2 in CID NULL. Test: Send Transaction Rq Audit Cap, CID=NULL, TID=CHOOSE
Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to NULL
AUDIT CAPABILITIES Command request with
TID set to CHOOSE
acceptable Audit Descriptor
sends a Transaction Reply containing
Action reply with
CID set to NULL
AUDIT CAPABILITIES Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401 "Protocol Error")
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.5
Text_Mode/
MG/
NO
Text_Mode/
MG/
NO/
BV
H248_MG_TXT_NO_BV_01 Init: 1 eph term=TID1 in CID=CID1 with event descriptor. Test: Receive Transaction Rq Notify, CID=CID1, TID=TID1, valid ReqID and ObsEv
Initial condition: an Events Descriptor with specific RequestID was set at the IUT
for a specific Termination (TID1) in a specific Context (CID1). The IUT has detected the Events(s)
Ensure that the IUT, in order to indicate the detected event(s), sends a Transaction Request
containing:
Action request with
CID set to a specific CID1
NOTIFY Command request with
TID set to TID1
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events
for a specific Termination (TID1) in a specific Context (CID1).
The IUT has detected the Events(s).
User Action: Generate events to create Notify Request.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.7
H248_MG_TXT_NO_BV_02 Init: 1 phy term=TID1 in CID=NULL with event descriptor. Test: Receive Transaction Rq Notify, CID=NULL, TID=TID1, valid ReqID and ObsEv
Initial condition: an Events Descriptor with specific RequestID was set at the IUT
for a specific physical Termination (TID1) in the NULL Context. The IUT has detected
the Event(s).
Ensure that the IUT, in order to indicate the detected event(s), sends a Transaction
Request containing:
Action request with
CID set to NULL
NOTIFY Command request with
TID set to TID1
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

Initial condition: an Events Descriptor with specific RequestID was set at the IUT
for a specific physical Termination (TID1) in the NULL Context.
The IUT has detected the Event(s).
User Action: Generate events to create Notify Request.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.7
H248_MG_TXT_NO_BV_03 Selection criteria: Event descriptor implemented and set at a Termination
Initial condition: an Events Descriptor with specific RequestID was set at the IUT
for the ROOT Termination. The IUT has detected the Event(s).
Ensure that the IUT, in order to indicate the detected event(s), sends a
Transaction Request containing:
Action request with
CID set to a specific NULL
NOTIFY Command request with
TID set to ROOT
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events
User Action: Generate events to create Notify Request.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.7
Text_Mode/
MG/
SC
Text_Mode/
MG/
SC/
BV
H248_MG_TXT_SC_BV_01 Initial condition: 2 Terminations (TID1 and TID2) in Context CID1
will be taken out of service after a specified ServerChangeDelay, sends a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

Initial condition: 2 Terminations (TID1 and TID2) in Context CID1
User Action: Take TID1 out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_02 Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4)
in Context CID2.
Ensure that the IUT, in order to indicate that specific Terminations (TID1 and TID2) within a specific Context (CID1)
will be taken out of service after a specified ServerChangeDelay, sends a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4)
in Context CID2.
User Action: Take all Terminations out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_03 Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2
Ensure that the IUT, in order to indicate that a specific Terminations (TID1 and TID2) within a specific Context (CID1)
will be taken out of service after a specified ServerChangeDelay, sends a Transaction Request containing:
Action request with
CID set to ALL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2
User Action: Take all Terminations out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_04 Initial condition: 2 Terminations (TID1 and TID2) in NULL context
Ensure that the IUT, in order to indicate that a specific Termination (TID1)
will be taken out of service after a specified ServerChangeDelay, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
Initial condition: 2 Terminations (TID1 and TID2) in NULL context.
User Action: Take Termination TID1 out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_05 Initial condition: 2 physical Terminations (TID1 and TID2) in NULL context
Ensure that the IUT, in order to indicate that the Terminations TID1 and TID2
will be taken out of service after a specified ServerChangeDelay, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
Initial condition: 2 physical Terminations (TID1 and TID2) in NULL context.
User Action: Take all Terminations out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_06 Initial condition: any
Ensure that the IUT, in order to indicate that the whole MG
will be taken immediately out of service, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 908
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
Initial condition: any
User Action: Take the whole Media Gateway out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_07 Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2
Ensure that the IUT, in order to indicate that a specific Termination (TID1) in a Context (CID1)
will be taken out of service after a specified ServerChangeDelay, sends a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 905
("Termination taken out of service")
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2.
User Action: Take TID1 out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_08 Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2
Ensure that the IUT, in order to indicate that all Terminations within a specific Context (CID1)
will be taken out of service after a specified ServerChangeDelay, sends a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 905
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2.
User Action: Take all Terminations out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_09 Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2
Ensure that the IUT, in order to indicate that a specific Terminations (TID1 and TID2) within all Contexts
will be taken out of service after a specified ServerChangeDelay, sends a Transaction Request containing:
Action request with
CID set to ALL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 905
("Termination taken out of service")
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2
User Action: Take all Terminations out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_10 Initial condition: 2 physical Terminations (TID1 and TID2) in NULL context
Ensure that the IUT, in order to indicate that a specific Termination (TID1)
will be taken immediately out of service, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 905
("Termination taken out of service")
Initial condition: 2 physical Terminations (TID1 and TID2) in NULL context.
User Action: Take Termination TID1 out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_11 Initial condition: 2 Terminations (TID1 and TID2) in NULL context
Ensure that the IUT, in order to indicate that the physical Terminations TID1 and TID2
will be taken immediately out of service, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 905
("Termination taken out of service")
Initial condition: any
User Action: Take all Terminations out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_12 Initial condition: any
Ensure that the IUT, in order to indicate that the whole MG
will be taken immediately out of service, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 908
("Termination taken out of service")
Initial condition: any
User Action: Take the whole Media Gateway out of service
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_13 Initial condition: 2 physical Terminations (TID1 and TID2) in NULL context which are out of service
Ensure that the IUT, in order to indicate that service will be restored for all Terminations
(TID1 and TID2), sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeReason set to value 900
("Service Restored")
Initial condition: 2 physical Terminations (TID1 and TID2) in NULL context which are out of service
User Action: Restore All Terminations
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
H248_MG_TXT_SC_BV_14 Initial condition: 2 physical Terminations (TID1 and TID2) in NULL context which are out of service
Ensure that the IUT, in order to indicate that service will be restored for Termination TID1
in the NULL context, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeReason set to value 900
("Service Restored")
Initial condition: 2 physical Terminations (TID1 and TID2) in NULL context which are out of service
User Action: Restore All Terminations
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.8
Text_Mode/
MG/
AM
Text_Mode/
MG/
AM/
BV
H248_MG_TXT_AM_BV_01 Initial condition: idle
Ensure that the IUT, upon cold start, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Restart

Initial condition: idle
User Action: Cold start the Media Gateway.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.2
H248_MG_TXT_AM_BV_02 Initial condition: idle
Ensure that the IUT, upon cold start, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
TimeStamp

Initial condition: idle
User Action: Cold start the Media Gateway.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.2
H248_MG_TXT_AM_BV_03 Initial condition: idle
Ensure that the IUT, upon cold start, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor with
ServiceChangeReason set to 901("Cold Boot")

Initial condition: idle
User Action: Cold start the Media Gateway.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.2
H248_MG_TXT_AM_BV_04 Initial condition: idle
Ensure that the IUT, upon cold start, in order to indicate a new address
for subsequent communication, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor with
ServiceChangeAddress (for further communication)

Initial condition: idle
User Action: Cold start the Media Gateway.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.2
H248_MG_TXT_AM_BV_05 Initial condition: IUT has sent a valid Transaction Request to perform a cold start
(e.g. ServiceChangeCommand request with the ServiceChangeMethod
set to Restart).
Ensure that the IUT, upon receipt of a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change Descriptor with
ServiceChangeMgcId
resends the valid Transaction Request to the MGC address given in the ServiceChangeMgcId.

Initial condition: IUT has sent a valid Transaction Request to perform a cold start
(e.g. ServiceChangeCommand request with the ServiceChangeMethod
set to Restart).
User Action: Cold start the Media Gateway.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.2
H248_MG_TXT_AM_BV_06
Initial condition: IUT has sent a valid Transaction Request to perform a cold start
(e.g. ServiceChangeCommand request with the ServiceChangeMethod
set to RESTART
Ensure that the IUT, after timer expiry without having received the appropriate
Transaction Reply from its primary MGC resend the valid Transaction Request to
its secondary MGC to perform a cold start.

Initial condition: IUT has sent a valid Transaction Request to perform a cold start
(e.g. ServiceChangeCommand request with the ServiceChangeMethod
set to RESTART
User Action: Cold start the Media Gateway.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.2
H248_MG_TXT_AM_BV_07 Initial condition: idle
Ensure that the IUT, upon cold start, having sent a ServiceChangeCommand request
with the ServiceChangeMethod parameter set to "RESTART", on receipt of a
message other than the corresponding ServiceChange Command reply, the IUT sends
a Transaction Reply containing error descriptor (value, 505, "Command received
before Restart Response").

Initial condition: idle
User Action: Cold start the Media Gateway.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.2 last paragraph
H248_MG_TXT_AM_BV_08 Initial condition: idle
Ensure that the IUT, upon cold start, sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to 2

Initial condition: idle
User Action: Cold start the Media Gateway.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.3
H248_MG_TXT_AM_BV_09 Initial condition: IUT has sent a valid Transaction Request to perform a cold start
(e.g. ServiceChangeCommand request with the ServiceChangeMethod
set to RESTART)
Ensure that the IUT, on receipt of a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeVersion set to 3
rejects subsequent Transaction Request with a Transaction Reply message containing
Error Descriptor (value 406, "Version not supported")

Initial condition: IUT has sent a valid Transaction Request to perform a cold start
(e.g. ServiceChangeCommand request with the ServiceChangeMethod
set to RESTART)
User Action: Cold start the Media Gateway.
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.2
H248_MG_TXT_AM_BV_10 Initial condition: IUT lost communuication with the MGC but it was subsequently
restored to the same MGC.
Ensure that the IUT, in order to indicate the previous lost of communication,
sends a Transation Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Disconnect
ServiceChangeReason set to value 906
("Loss of lower layer connectivity")

Initial condition: IUT lost communuication with the MGC but it was subsequently
restored to the same MGC.
User Action:
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.4
H248_MG_TXT_AM_BV_11 Initial condition: any
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Handoff
ServiceChangeResearch set to value 903
("MGC directed change")
ServiceChangeMgcID set to the designated MGC address

Sends a Transaction Reply containing:
Action reply with:
CID set to NULL
SERVICE CHANGE Command reply with:
TID set to ROOT
User Action:
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.5
H248_MG_TXT_AM_BV_13 Initial condition: IUT received a Service Change command request with ServiceChangeMethod
set to Handoff together with a designated MGC address
Ensure that the IUT, in order to establish a new connection to the designated MGC,
sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Handoff
ServiceChangeResearch set to value 903
("Loss of lower layer connectivity")

Initial condition: IUT received a Service Change command request with ServiceChangeMethod
set to Handoff together with a designated MGC address
User Action:
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 11.5
Text_Mode/
MG/
TR
Text_Mode/
MG/
TR/
BV
H248_MG_TXT_TR_BV_01 Ensure that the IUT, on receipt of a Megaco message containing
Transaction Request with
TransID set to TransID1
acceptable Action request and Command request
sends a Megaco message containing
Transaction Reply with
TransID set to TransID1
acceptable Action reply and Command reply
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 8
H248_MG_TXT_TR_BV_02 VOID removed as no such requirement)
the IUT has sent a valid Transaction Reply
of the corresponding Transaction Response Acknowledge, resends the previous Transaction Reply
the IUT has sent a valid Transaction Reply
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
PLEASE NOTE: This scenario was deprecated from the ETSI test specification
H248_MG_TXT_TR_BV_03 Selection criteria: 3 way handshake procedure supported
Initial condition: IUT has sent a valid Transaction Request with a Transaction ID set to TransID1
Ensure that the IUT, on receipt of a Megaco message containing
Transaction Reply with
TransID set to TransID1
acceptable Action reply and Command reply
sends a Megaco message containing
Transaction Response Acknowledge with
TransID set to TransID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 8
H248_MG_TXT_TR_BV_04 Selection criteria: Transaction Timer implemented
Initial condition: IUT has sent a valid Transaction Request with
a Transaction ID set to TransID1.
Ensure that the IUT, on expiry of the Transaction Timer without
receipt of neither a Transaction Reply nor a Transaction Pending,
resends the previous Transaction Request
a Transaction ID set to TransID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 8
H248_MG_TXT_TR_BV_05 Selction criteria: Transaction Timer implemented
Initial condition: After sending a valid Transaction Request
the IUT has received a valid Transaction Pending.
Ensure that the IUT, on expiry of the Transaction Timer without receipt
of the corresponding Transaction Reply or another Transaction Pending,
resends the Transaction Request
the IUT has received a valid Transaction Pending.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 8
H248_MG_TXT_TR_BV_06 Selection criteria: Transaction Timer implemented
Initial condition: After sending a valid Transaction Request, the IUT has received a valid Transaction Pending.
Ensure that the IUT on receipt of a Megaco message containing
Transaction Reply with
TransID set to TransID1
acceptable Action reply and Command reply
sends a Megaco message containing
Transaction Response Acknowledge with
TransID set to TransID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 8
Text_Mode/
MGC
H248_MGC_TXT_Start_01 Send ServiceChangeReq, wait for response
User Action: None
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
Text_Mode/
MGC/
AD
Text_Mode/
MGC/
AD/
BV
H248_MGC_TXT_AD_BV_01 Initial condition: any
Ensure that the IUT, in order to create an ephemeral termination in a new context,
send a Transaction Request containing:
Action request with
CID set to CHOOSE
ADD Command request with
TID set to Choose
User Action: None
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MGC_TXT_AD_BV_02 Initial condition: Termination TID1 exists in the NULL Context
Ensure that the IUT, in order to add an existing physical Termination
from the NULL Context to a MG-assigned Context,
send a Transaction Request containing:
Action request with
CID set to CHOOSE
ADD Command request with
TID set to TID1
User Action: Generate an Add Request adding a physical termination TID1 to a context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MGC_TXT_AD_BV_03 Initial condition: 2 Terminations (TID1 and TID2) exists in the NULL Context
Ensure that the IUT, in order to add 2 existing physical Terminations (TID1 AND TID2)
from the NULL Context to a MG-assigned Context,
send a Transaction Request containing:
Action request with
CID set to CHOOSE
ADD Command request with
TID set to ALL
User Action: Generate an Add Request adding the 2 physical terminations to a context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MGC_TXT_AD_BV_04 Initial condition: Termination TID1 exists in Context CID1
Ensure that the IUT, in order to create an ephemeral termination
in an already existing specific context,
send a Transaction Request containing:
Action request with
CID set to CID1
ADD Command request with
TID set to CHOOSE
User Action: Generate an Add Request creating terminations to an existing context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 clause 7.2.1
H248_MGC_TXT_AD_BV_05 Initial condition: 2 physical Termination (TID2 and TID3) exist in the NULL Context
An ephemeral Termination (TID1) exists in Context CID1
Ensure that the IUT, in order to add two physical Terminations (TID2 and TID3)
from the NULL Context to an already existing specific Context,
send a Transaction Request containing:
Action request with
CID set to CID1
ADD Command request with
TID set to ALL
An ephemeral Termination (TID1) exists in Context CID1
User Action: Generate an Add Request to add 2 physical terminations to an existing context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.1
H248_MGC_TXT_AD_BV_06 Initial condition: 2 physical Termination (TID1 and TID2) exist in the NULL Context
An ephemeral Termination, TID3 exists in Context CID1
Ensure that the IUT, in order to add an existing physical Terminations (TID1)
from the NULL Context to an already existing specific Context,
send a Transaction Request containing:
Action request with
CID set to CID1
ADD Command request with
TID set to TID1
An ephemeral Termination exists in Context CID1
User Action: Generate an Add Request to add TID1 physical termination to an existing context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.1
H248_MGC_TXT_AD_BV_07 Initial condition: Termination TID1 is in Context CID1
Termination TID2 is in Context CID2.
Ensure that the IUT, in order to add to each of two already existing Contexts
an ephemeral Termination (of the same type) send a Transaction Request containing:
Action request with
CID set to ALL
ADD Command request with
TID set to CHOOSE
*** Not available in this release ***
Termination TID2 is in Context CID2.
User Action: Generate an Add Request to add an ephemeral termination to each of the two existing contexts.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.1
Text_Mode/
MGC/
MD
Text_Mode/
MGC/
MD/
BV
H248_MGC_TXT_MD_BV_01 Selection criteria: Wildcard mechanism implemented
Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
Ensure that the IUT, in order to modify in the same way two existing ephemeral Terminations(TID1, TID2)
in a specific Context (CID1) sends a Transaction Request containing:
Action request with
CID set to CID1
MODIFY Command request with
TID set to ALL
User Action: Generate an Modify Request to modify two existing ephemeral terminations in an existing context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1]clause 7.2.2
H248_MGC_TXT_MD_BV_02 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1
Ensure that the IUT, in order to modify an existing ephemeral Terminations(TID1)
in a specific Context (CID1) sends a Transaction Request containing:
Action request with
CID set to CID1
MODIFY Command request with
TID set to TID1
User Action: Generate an Modify Request to modify two existing ephemeral terminations in an existing context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.2
H248_MGC_TXT_MD_BV_03 *** Not available in this release ***
Initial condition: any
Ensure that the IUT, in order to modify all Terminations
in all Contexts (e.g. 4 ephemeral Terminations in 2 Contexts) sends a Transaction Request containing:
Action request with
CID set to ALL
MODIFY Command request with
TID set to ALL
2 Terminations (TID3 and TID4) exist in Context CID2.
User Action: Generate an Modify Request to modify all ephemeral terminations in all contexts.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.2
H248_MGC_TXT_MD_BV_04 Selection criteria: Wildcard mechanism implemented
Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1,
2 Terminations (TID3 and TID4) exist in Context CID2.
Ensure that the IUT, in order to modify Termination (TID3) by addressing
the Contexts (CID2) with wildcard ALL, sends a Transaction Request containing:
Action request with
CID set to ALL
MODIFY Command request with
TID set to TID3
2 Terminations (TID3 and TID4) exist in Context CID2.
User Action: Generate an Modify Request to modify ephemeral termination (TID3) in all contexts.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.2
H248_MGC_TXT_MD_BV_05 Selection criteria: Wildcard mechanism implemented
Initial condition: any
Ensure that the IUT, in order to modify all Terminations (e.g. physical terminations)
in the NULL Context in the same way, sends a Transaction Request containing:
Action request with
CID set to NULL
MODIFY Command request with
TID set to ALL
User Action: Generate an Modify Request to modify two physical terminations in the NULL context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.2
H248_MGC_TXT_MD_BV_06 Initial condition: any
Ensure that the IUT, in order to modify a specific Terminations (e.g. physical terminations, TID1)
in the NULL Context, sends a Transaction Request containing:
Action request with
CID set to NULL
MODIFY Command request with
TID set to TID1
User Action: Generate an Modify Request to modify two physical terminations in the NULL context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.2
H248_MGC_TXT_MD_BV_07 Selection criteria: ROOT Termination implemented
Initial condition: any
Ensure that the IUT, in order to modify properties of the entire gateway
sends a Transaction Request containing:
Action request with
CID set to NULL
MODIFY Command request with
TID set to ROOT
User Action: Generate an Modify Request to modify properties of the entire gateway.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.2
Text_Mode/
MGC/
SU
Text_Mode/
MGC/
SU/
BV
H248_MGC_TXT_SU_BV_01 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1
Ensure that the IUT, in order to subtract all Terminations(TID1 and TID2)
in a specific Context (CID1) sends a Transaction Request containing:
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to ALL
User Action: Generate a Subtract Request to subtract all terminations from an existing context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.3
H248_MGC_TXT_SU_BV_02 Selection criteria: wildcardReturn Request procedure implemented
Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
Ensure that the IUT, in order to subtract all Terminations(TID1 and TID2)
from a specific Context (CID1) by using the wildcardREturn parameter, sends a Transaction Request containing:
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to ALL
wildcardReturn request
empty Audit Descriptor
User Action: Generate a Subtract Request with wildcardReturn to subtract all terminations from an existing context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.3
H248_MGC_TXT_SU_BV_03 Initial condition: 1 Terminations (TID1) exists in Context CID1
Ensure that the IUT, in order to subtract a Termination (TID1)
from a specific Context (CID1), sends a Transaction Request containing:
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to TID1
User Action: Generate an Subtract Request to subtract TID1 termination from an existing context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.3
H248_MGC_TXT_SU_BV_04 Selection criteria: wildcardReturn Request procedure implemented
Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1,
2 Terminations (TID3, TID4) exist in Context CID2.
Ensure that the IUT, in order to subtract all Terminations (TID1, TID2, TID3, and TID4)
from all Contexts (CID1 and CID2) by using the wildcard Response parameter, sends a Transaction Request containing:
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to ALL
wildcard Return request
empty Audit descriptor
User Action: Generate a Subtract Request with wildcardReturn to subtract all terminations from all contexts.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.3
H248_MGC_TXT_SU_BV_05 Selection criteria: wildcardReturn Request procedure implemented
Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1,
2 Terminations (TID3, TID4) exist in Context CID2.
Ensure that the IUT, in order to subtract Termination (TID3)
by addressing Context CID2 with the wildcard ALL, sends a Transaction Request containing:
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to TID3
empty Audit descriptor
User Action: Generate a Subtract Request to subtract termination TID3 using wildcard context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.3
Text_Mode/
MGC/
MO
Text_Mode/
MGC/
MO/
BV
H248_MGC_TXT_MO_BV_01 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1,
2 Terminations (TID3, TID4) exist in Context CID2.
Ensure that the IUT, in order to move the Termination TID1 and TID2
to specific Context CID2, sends a Transaction Request containing:
Action request with
CID set to CID2
MOVE Command request with
TID set to ALL
User Action: Generate a Move Request to move termination TID1 and TID2 to CID2 context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.4
H248_MGC_TXT_MO_BV_02 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1,
2 Terminations (TID3, TID4) exist in Context CID2.
Ensure that the IUT, in order to move the Termination TID1
to specific Context CID2, sends a Transaction Request containing:
Action request with
CID set to CID2
MOVE Command request with
TID set to TID1
User Action: Generate a Move Request to move termination TID1 to CID2 context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.4
H248_MGC_TXT_MO_BV_03 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1
Ensure that the IUT, in order to move two specific Termination (TID1 and TID2)
to a newly assigned Context CID2, sends a Transaction Request containing:
Action request with
CID set to CHOOSE
MOVE Command request with
TID set to ALL
User Action: Generate a Move Request to move termination TID1 and TID2 to a newly assigned CID2 context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.4
H248_MGC_TXT_MO_BV_04 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1
Ensure that the IUT, in order to move specific Termination (TID1)
to a newly assigned Context CID2, sends a Transaction Request containing:
Action request with
CID set to CHOOSE
MOVE Command request with
TID set to TID1
User Action: Generate a Move Request to move termination TID1 to a newly assigned CID2 context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.4
Text_Mode/
MGC/
AV
Text_Mode/
MGC/
AV/
BV
H248_MGC_TXT_AV_BV_01 Selection criteria: Wildcard mechanism implemented
Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
Ensure that the IUT, in order to get the current values of parameters for all Terminations (TID1 and TID2)
within a specific Context CID1, sends a Transaction Request containing:
Action request with
CID set to CID1
AUDIT VALUE Command request with
TID set to ALL
acceptable Audit Descriptor
User Action: Generate a Audit Value Request to get current values for all Terminations in a context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AV_BV_02 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1
Ensure that the IUT, in order to get the current values of parameters of a specific termination (TID1)
within a specific Context CID1, sends a Transaction Request containing:
Action request with
CID set to CID1
AUDIT VALUE Command request with
TID set to TID1
acceptable Audit Descriptor
User Action: Generate a Audit Value Request to get current values for Termination TID1 in a context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AV_BV_03 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1,
2 Terminations (TID3 and TID4) exist in Context CID2.
Ensure that the IUT, in order to get the current values of parameters for all Terminations
within all Contexts, sends a Transaction Request containing:
Action request with
CID set to ALL
AUDIT VALUE Command request with
TID set to ALL
acceptable Audit Descriptor
2 Terminations (TID3 and TID4) exist in Context CID2.
User Action: Generate a Audit Value Request to get current values for all Terminations in all Contexts.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AV_BV_04 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1
Ensure that the IUT, in order to get the (non-NULL) ContextID in which a specific Termination (TID1)
currently exists, sends a Transaction Request containing:
Action request with
CID set to ALL
AUDIT VALUE Command request with
TID set to TID1
empty Audit Descriptor
User Action: Generate a Audit Value Request to get the Context ID for a specific Termination (TID1).
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AV_BV_05 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1,
2 Terminations (TID3 and TID4) exist in Context CID2.
Ensure that the IUT, in order to get the current list of all Context IDs,
sends a Transaction Request containing:
Action request with
CID set to ALL
AUDIT VALUE Command request with
TID set to ROOT
empty Audit Descriptor
2 Terminations (TID3 and TID4) exist in Context CID2.
User Action: Generate a Audit Value Request to get current list of all Context IDs.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AV_BV_06 Initial condition: 2 Physical Terminations (TID1 and TID2) exist in NULL Context
Ensure that the IUT, in order to get the current values of parameters of all Terminations (TID1 and TID2)
within the NULL Context, sends a Transaction Request containing:
Action request with
CID set to NULL
AUDIT VALUE Command request with
TID set to ALL
acceptable Audit Descriptor
User Action: Generate a Audit Value Request to get current values of parameters for all physical Terminations in NULL context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AV_BV_07 Initial condition: 2 Physical Terminations (TID1 and TID2) exist in NULL Context
Ensure that the IUT, in order to get the current values of parameters of a specific Termination (TID1)
outside of any Context, sends a Transaction Request containing:
Action request with
CID set to NULL
AUDIT VALUE Command request with
TID set to TID1
acceptable Audit Descriptor
User Action: Generate a Audit Value Request to get current values of parameters of a specific Termination (TID1).
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AV_BV_08 Selection criteria: ROOT Termination implemented
Initial condition: any
Ensure that the IUT, in order to get the current values of parameters which are related to the MG
state and events, sends a Transaction Request containing:
Action request with
CID set to NULL
AUDIT VALUE Command request with
TID set to ROOT
acceptable Audit Descriptor
User Action: Generate a Audit Value Request to get current values of parameters which are related to the MG state and event.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
Text_Mode/
MGC/
AC
Text_Mode/
MGC/
AC/
BV
H248_MGC_TXT_AC_BV_01 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1
Ensure that the IUT, in order to get the possible values of parameters for all ( ephemeral ) Terminations (TID1 and TID2)
within a specific Context CID1, sends a Transaction Request containing:
Action request with
CID set to CID1
AUDIT CAPABILITY Command request with
TID set to ALL
acceptable Audit Descriptor
User Action: Generate a Audit Capability Request to get possible values for all Terminations in a context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AC_BV_02 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1
Ensure that the IUT, in order to get the possible values of parameters for a specific Termination (TID1)
within a specific Context CID1, sends a Transaction Request containing:
Action request with
CID set to CID1
AUDIT CAPABILITY Command request with
TID set to TID1
acceptable Audit Descriptor
User Action: Generate a Audit Capability Request to get possible values for a specific Termination in a context.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AC_BV_03 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1,
2 Terminations (TID3 and TID4) exist in Context CID2.
Ensure that the IUT, in order to get the possible values of parameters of all Terminations
within all Contexts, sends a Transaction Request containing:
Action request with
CID set to ALL
AUDIT CAPABILITY Command request with
TID set to ALL
acceptable Audit Descriptor
2 Terminations (TID3 and TID4) exist in Context CID2.
User Action: Generate a Audit Capability Request to get possible values for all Terminations in all Contexts.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AC_BV_04 Selection criteria: Wildcard mechanism implemented
Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
Ensure that the IUT, in order to get the (non_NULL) ContexxtID in which a specific Termination (TID1)
currently exists, sends a Transaction Request containing:
Action request with
CID set to ALL
AUDIT CAPABILITY Command request with
TID set to TID1
empty Audit Descriptor
User Action: Generate a Audit Capability Request to get the Context ID for a specific Termination (TID1).
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AC_BV_05 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1,
2 Terminations (TID3 and TID4) exist in Context CID2.
Ensure that the IUT, in order to get the current list of all Context ids,
sends a Transaction Request containing:
Action request with
CID set to ALL
AUDIT CAPABILITY Command request with
TID set to ROOT
acceptable Audit Descriptor
2 Terminations (TID3 and TID4) exist in Context CID2.
User Action: Generate a Audit Capability Request to get the current list of all Context IDs.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AC_BV_06 Initial condition: 2 Terminations (TID1 and TID2) exist in the NULL Context
Ensure that the IUT, in order to get the possible values of parameters of all phsycial Terminations
(TID1 and TID2) in the NULL Context, sends a Transaction Request containing:
Action request with
CID set to NULL
AUDIT CAPABILITY Command request with
TID set to ALL
acceptable Audit Descriptor
User Action: Generate a Audit Capability Request to get possible values for all physical Terminations.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AC_BV_07 Initial condition: 2 Terminations (TID1 and TID2) exist in the NULL Context
Ensure that the IUT, in order to get the possible values of parameters of a specific Termination
(TID1) outside of any Context, sends a Transaction Request containing:
Action request with
CID set to NULL
AUDIT CAPABILITY Command request with
TID set to TID1
acceptable Audit Descriptor
User Action: Generate a Audit Capability Request to get possible values of a specific physical Termination.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
H248_MGC_TXT_AC_BV_08 Selection criteria: ROOT Termination implemented
Initial condition: any
Ensure that the IUT, in order to get the possible values of parameters which are related to the MG
state and events, sends a Transaction Request containing:
Action request with
CID set to NULL
AUDIT CAPABILITY Command request with
TID set to ROOT
acceptable Audit Descriptor
User Action: Generate a Audit Capability Request to get possible values on the MG state and events.
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.5
Text_Mode/
MGC/
NO
Text_Mode/
MGC/
NO/
BV
H248_MGC_TXT_NO_BV_01 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1. An Events descriptor with
specific RequestID set for a specific Termination (TID1) in a specific Context (CID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to CID1
NOTIFY Command request with
TID set to TID1
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to CID1
NOTIFY Command reply with
TID set to TID1
specific Termination (TID1) in a specific Context (CID1)
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BV_02 Initial condition: An Events descriptor with specific Request ID was set for a
specific physical Termination (TID1) in the NULL Context.
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to NULL
NOTIFY Command request with
TID set to TID1
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to NULL
NOTIFY Command reply with
TID set to TID1
specific physical Termination (TID1) in the NULL Context.
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BV_03 Initial condition: An Events descriptor with specific Request ID was set
for the ROOT Termination.
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to NULL
NOTIFY Command request with
TID set to ROOT
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to NULL
NOTIFY Command reply with
TID set to ROOT
for the ROOT Termination.
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
Text_Mode/
MGC/
NO/
BI
H248_MGC_TXT_NO_BI_01 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1. An Events descriptor with
specific RequestID set for a specific Termination (TID1) in a specific Context (CID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to CID1
NOTIFY Command request with
TID set to CHOOSE
ObservedEvents Descriptor
RequestID set to 0
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to CID1
NOTIFY Command reply with
TID set to CHOOSE
Error descriptor (value 410, "Incorrect Identifier")
specific Termination (TID1) in a specific Context (CID1)
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BI_02 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1. An Events descriptor with
specific RequestID set for a specific Termination (TID1) in a specific Context (CID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to CID1
NOTIFY Command request with
TID set to CHOOSE
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to CID1
NOTIFY Command reply with
TID set to CHOOSE
Error descriptor (value 401, "Protocol Error")
specific Termination (TID1) in a specific Context (CID1)
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BI_03 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1. An Events descriptor with
specific RequestID set for a specific Termination (TID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to CID1
NOTIFY Command request with
TID set to ALL
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to CID1
NOTIFY Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error")
specific Termination (TID1) in a specific Context (CID1)
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BI_04 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1. An Events descriptor with
specific RequestID set for a specific Termination (TID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to CID1
NOTIFY Command request with
TID set to ROOT
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to CID1
NOTIFY Command reply with
TID set to ROOT
Error descriptor (value 410, "Incorrect indentifier")
specific Termination (TID1) in a specific Context (CID1)
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clauses 7.2.7 and 6.2.5
H248_MGC_TXT_NO_BI_05 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1. An Events descriptor with
specific RequestID set for a specific Termination (TID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to CHOOSE
NOTIFY Command request with
TID set to CHOOSE
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to CHOOSE
NOTIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error")
specific Termination (TID1) in a specific Context (CID1)
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BI_06 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1. An Events descriptor with
specific RequestID set for a specific Termination (TID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to CHOOSE
NOTIFY Command request with
TID set to ALL
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to CHOOSE
NOTIFY Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error")
specific Termination (TID1) in a specific Context (CID1)
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BI_07 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1. An Events descriptor with
specific RequestID set for a specific Termination (TID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to CHOOSE
NOTIFY Command request with
TID set to TID1
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to CHOOSE
NOTIFY Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error")
specific Termination (TID1) in a specific Context (CID1)
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BI_08 Initial condition: An Events descriptor with specific RequestID set for the ROOT Termination
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to CHOOSE
NOTIFY Command request with
TID set to ROOT
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to CHOOSE
NOTIFY Command reply with
TID set to ROOT
Error descriptor (value 410, "Incorrect identifier")
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clauses 7.2.7 and 6.2.5
H248_MGC_TXT_NO_BI_09 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
2 Terminations (TID3 and TID4) exist in Context CID2.
An Events descriptor with specific RequestID set for a
specific Termination (TID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to ALL
NOTIFY Command request with
TID set to CHOOSE
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to ALL
NOTIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error")
2 Terminations (TID3 and TID4) exist in Context CID2.
An Events descriptor with specific RequestID set for a
specific Termination (TID1).
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BI_10 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
2 Terminations (TID3 and TID4) exist in Context CID2.
An Events descriptor with specific RequestID set for a
specific Termination (TID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to ALL
NOTIFY Command request with
TID set to ALL
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to ALL
NOTIFY Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error")
2 Terminations (TID3 and TID4) exist in Context CID2.
An Events descriptor with specific RequestID set for a
specific Termination (TID1).
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BI_11 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
2 Terminations (TID3 and TID4) exist in Context CID2.
An Events descriptor with specific RequestID set for a
specific Termination (TID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to ALL
NOTIFY Command request with
TID set to TID1
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to ALL
NOTIFY Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error")
2 Terminations (TID3 and TID4) exist in Context CID2.
An Events descriptor with specific RequestID set for a
specific Termination (TID1).
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BI_12 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
2 Terminations (TID3 and TID4) exist in Context CID2.
An Events descriptor with specific RequestID set for a
specific Termination (TID1)
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to ALL
NOTIFY Command request with
TID set to ROOT
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to ALL
NOTIFY Command reply with
TID set to ROOT
Error descriptor (value 410, "Incorrect indentifier")
2 Terminations (TID3 and TID4) exist in Context CID2.
An Events descriptor with specific RequestID set for a
specific Termination (TID1).
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clauses 7.2.7 and 6.2.5
H248_MGC_TXT_NO_BI_13 Initial condition: 2 Terminations (TID1 and TID2) exist in the NULL Context
An Events descriptor with specific RequestID set for a
specific Termination (TID1).
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to NULL
NOTIFY Command request with
TID set to CHOOSE
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to NULL
NOTIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error")
An Events descriptor with specific RequestID set for a
specific Termination (TID1).
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
H248_MGC_TXT_NO_BI_14 Initial condition: 2 Terminations (TID1 and TID2) exist in the NULL Context
An Events descriptor with specific RequestID set for a
specific Termination (TID1).
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to NULL
NOTIFY Command request with
TID set to ALL
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events

sends a Transaction Reply containing:
Action reply with
CID set to NULL
NOTIFY Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error")
An Events descriptor with specific RequestID set for a
specific Termination (TID1).
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.7
Text_Mode/
MGC/
SC
Text_Mode/
MGC/
SC/
BV
H248_MGC_TXT_SC_BV_01 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CID1
SERVICE CHANGE Command reply with
TID set to TID1
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_02 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CID1
SERVICE CHANGE Command reply with
TID set to ALL
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_04 Initial condition: 2 Terminations (TID1 and TID2) exist in NULL Context.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to TID1
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_05 Initial condition: 2 Terminations (TID1 and TID2) exist in NULL Context.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CID1
SERVICE CHANGE Command reply with
TID set to ALL
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_06 Initial condition: any
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 908
("MG impending Failure")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_07 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CID1
SERVICE CHANGE Command reply with
TID set to TID1
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_08 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CID1
SERVICE CHANGE Command reply with
TID set to ALL
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_10 Initial condition: 2 Terminations (TID1 and TID2) exist in NULL Context.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to TID1
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_11 Initial condition: 2 Terminations (TID1 and TID2) exist in NULL Context.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CID1
SERVICE CHANGE Command reply with
TID set to ALL
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_12 Initial condition: any
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeResearch set to value 908
("MG impending Failure")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_13 Initial condition: MGC has received a Transaction Request with a valid Service Change Command
with ServiceChangeMethod set to "Forced" (the CID was set to CID1 and the TIDs
were set to TID1 and TID2).
Ensure that the IUT, after having sent the corresponding Transaction Reply, sends a new
Transaction Request with a:
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to TID1
acceptable descriptors

Initial condition: MGC has received a Transaction Request with a valid Service Change Command
with ServiceChangeMethod set to "Forced" (the CID was set to CID1 and the TIDs
were set to TID1 and TID2).
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_14 Initial condition: 2 physical Termination (TID1 and TID2) exist in the NULL Context and are out
of service
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeResearch set to value 900
("Service Restored")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to TID1
of service
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BV_15 Initial condition: 2 physical Termination (TID1 and TID2) exist in the NULL Context and are out
of service
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeResearch set to value 900
("Service Restored")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ALL
of service
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
Text_Mode/
MGC/
SC/
BI
H248_MGC_TXT_SC_BI_01 Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CHOOSE
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CHOOSE
SERVICE CHANGE Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error")

Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BI_02 Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CHOOSE
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CHOOSE
SERVICE CHANGE Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error")

Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BI_03 Initial condition: any
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CHOOSE
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CHOOSE
SERVICE CHANGE Command reply with
TID set to ROOT
Error descriptor (value 410, "Incorrect identifier")

Initial condition: any
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clauses 7.2.8 and 6.2.5
H248_MGC_TXT_SC_BI_04 Initial condition: any
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CHOOSE
SERVICE CHANGE Command request with
TID set to CHOOSE
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CHOOSE
SERVICE CHANGE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error")

Initial condition: any
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BI_05 Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CID1
SERVICE CHANGE Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error")

Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clauses 7.2.8 and 6.2.5
H248_MGC_TXT_SC_BI_06 Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to CHOOSE
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)

sends a Transaction Reply containing:
Action reply with
CID set to CID1
SERVICE CHANGE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error")

Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BI_07 Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1 were previously
taken out of service.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeResearch set to value 900
("Service Restored")

sends a Transaction Reply containing:
Action reply with
CID set to CID1
SERVICE CHANGE Command reply with
TID set to ALL
Error descriptor (e.g. value 411, "Protocol Error")

Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1 were previously
taken out of service.
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BI_08 Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1 were previously
taken out of service.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeResearch set to value 900
("Service Restored")

sends a Transaction Reply containing:
Action reply with
CID set to CID1
SERVICE CHANGE Command reply with
TID set to TID1
Error descriptor (value 435, "Termination ID is not specified in Context")

Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1 were previously
taken out of service.
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BI_09 Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1,
2 Termination (TID3 and TID4) exist in Context CID2

Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to ALL
SERVICE CHANGE Command request with
TID set to CHOOSE
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")

sends a Transaction Reply containing:
Action reply with
CID set to ALL
SERVICE CHANGE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error")

Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1,
2 Termination (TID3 and TID4) exist in Context CID2
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BI_10 Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1,
2 Termination (TID3 and TID4) exist in Context CID2

Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to ALL
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")

sends a Transaction Reply containing:
Action reply with
CID set to ALL
SERVICE CHANGE Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error")

Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1,
2 Termination (TID3 and TID4) exist in Context CID2
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BI_11 Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1,
2 Termination (TID3 and TID4) exist in Context CID2

Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to ALL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeResearch set to value 905
("Termination taken out of service")

sends a Transaction Reply containing:
Action reply with
CID set to ALL
SERVICE CHANGE Command reply with
TID set to ROOT
Error descriptor (value 410, "Incorrect identifier")

Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1,
2 Termination (TID3 and TID4) exist in Context CID2
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clauses 7.2.8 and 6.2.5
H248_MGC_TXT_SC_BI_12 Initial condition: 2 Terminations (TID1 and TID2) exist in NULL Context

Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to CHOOSE
acceptable Service Change Descriptor

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error")

Initial condition: 2 Termination (TID1 and TID2) exist in NULL Context
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
H248_MGC_TXT_SC_BI_13 Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1 and
2 Termination (TID3 and TID4) exist in Context CID2 were previously
taken out of service.
Ensure that the IUT, after receipt of a Transaction Request containing:
Action request with
CID set to ALL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeResearch set to value 900
("Service Restored")

sends a Transaction Reply containing:
Action reply with
CID set to ALL
SERVICE CHANGE Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error")

Initial condition: 2 Termination (TID1 and TID2) exist in Context CID1 and
2 Termination (TID3 and TID4) exist in Context CID2 were previously
taken out of service.
User Action: Set up the Initial Condition
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 7.2.8
Text_Mode/
MGC/
AM
Text_Mode/
MGC/
AM/
BV
H248_MGC_TXT_AM_BV_01 Initial condition: idle
Ensure that the IUT, in order to confirm the registration of a connected
MG within the cold start procedure, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeReason set to value 901 ("Cold Boot")
further acceptable ServiceChange parameters

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
TimeStamp set to a specific value
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 11.2
H248_MGC_TXT_AM_BV_02 Initial condition: idle
Ensure that the IUT, in order to change the address for further communication
within the cold start procedure, on receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeReason set to value 901 ("Cold Boot")
further acceptable ServiceChange parameters

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeAddress (for the further communication)
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 11.2
H248_MGC_TXT_AM_BV_03 Initial condition: idle
Ensure that the IUT, in order to reject the registration of a connected MG
within the cold start procedure, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeReason set to value 901 ("Cold Boot")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
further acceptable ServiceChange parameters

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeMgcId
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 11.2
H248_MGC_TXT_AM_BV_04 Initial condition: idle
Ensure that the IUT, in order to accept the proposed protocol version
within the cold start procedure, after receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeVersion set to 2
further acceptable ServiceChange parameters

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeVersion set to 2
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 11.2
H248_MGC_TXT_AM_BV_05 Initial condition: any
Ensure that the IUT, in order to switch back to a previous protocol version
within the cold start procedure, on receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeVersion set to 2
further acceptable ServiceChange parameters

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeVersion set to 1
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 11.3
H248_MGC_TXT_AM_BV_06 Initial condition: any
Ensure that the IUT, in order to announce within the cold start procedure
that the proposed protocol version cannot be supported, on receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeVersion set to 3
further acceptable ServiceChange parameters

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
Error descriptor (value 406, "Version Not Supported")
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 11.3
H248_MGC_TXT_AM_BV_07 Initial condition: any
Ensure that the IUT, on receipt of a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Disconnected
ServiceChangeReason set to value 906 ("Loss of lower layer connectivity")

sends a Transaction Reply containing:
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 11.4
H248_MGC_TXT_AM_BV_08 Initial condition: any
Ensure that the IUT, in order to handoff the MG to another MGC,

sends a Transaction Request containing:
Action request with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeMethod set to Handoff
ServiceChangeReason set to 903 ("MGC directed change")
ServiceChangeMgcId set to the designated MGC address
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 11.5
Text_Mode/
MGC/
TR
Text_Mode/
MGC/
TR/
BV
H248_MGC_TXT_TR_BV_01 Initial condition: any
Ensure that the IUT, on receipt of a Megaco message containing:
Transaction request with
TransID set to a TransID1
acceptable Action request and Command request

sends a Megaco message containing:
Transaction reply with
TransID set to a TransID1
acceptable Action reply and Command reply
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 8
H248_MGC_TXT_TR_BV_03 Selection criteria: 3 way handshake procedure supported
Initial condition: IUT has sent a valid Transaction Request with a Transaction ID
set to TransID1.
Ensure that the IUT, on receipt of a Megaco message containing:
Transaction Reply with
TransID set to a TransID1
acceptable Action request and Command request

sends a Megaco message containing:
Transaction Response Acknowledge with
TransID set to a TransID1
set to TransID1
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 8
H248_MGC_TXT_TR_BV_04 Selection criteria: Transaction Timer implemented
Initial condition: IUT has sent a valid Transaction Request with a Transaction ID
set to TransID1.
Ensure that the IUT, on expiry of the Transaction Timer without receipt of neither
a Transaction Reply nor a Transaction Pending, resends the previous Transaction
Request
set to TransID1.
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 8
H248_MGC_TXT_TR_BV_05 Selection criteria: Transaction Timer implemented
Initial condition: After sending a valid Transaction Request the IUT
has received a valid Transaction Pending.

Ensure that the IUT, on expiry of the Transaction Timer without receipt
of the corresponding Transaction Reply or another Transaction Pending,
resends the previous Transaction Request.
has received a valid Transaction Pending.
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 8
H248_MGC_TXT_TR_BV_06 Selection criteria: Transaction Timer implemented
Initial condition: After sending a valid Transaction Request the IUT
has received a valid Transaction Pending.

Ensure that the IUT, on receipt of a Megaco message containing:
Transaction Reply with
TransID set to TransID1
acceptable Action reply and Command reply

sends a Megaco message containing
Transaction Response Acknowledge with
TransID set to TransID1
has received a valid Transaction Pending.
User Action:
Config: Config1
SUT: MGC
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1] clause 8
Text_Mode/
CUSTOM
MG_TXT_2ADD Initial condition: any
Ensure that the IUT, will accept two adds. Descriptors can be set as user defines.

Initial condition: any
User Action: none
Config: Config1
SUT: MG or PG
Status: Not Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
Binary_Mode
Binary_Mode/
MG		 Media Gateway Compliance Test Routines
Binary_Mode/
MG/
Startup		 Initialize the interface and bring the MG out of restart.
MG_Startup_V_01 Waits for MG to send ServiceChangeReq, send Reply in response
Waits for MG to send ServiceChangeReq, send Reply in response
MG_Startup_I_01 Waits for MG to send ServiceChangeReq, send Reply with invalid ServiceChangeVersion in response
Waits for MG to send ServiceChangeReq, send Reply with invalid ServiceChangeVersion in response
Binary_Mode/
MG/
MG_AD		 Media gateway termination ADD test routines.
Binary_Mode/
MG/
MG_AD/
MG_AD_BV		 Media gateway termination ADD compliance verification routines.
H248_MG_AD_BV_01 Ensure that the IUT, on receipt of a Transaction request containing
Action request with CID set to CHOOSE ADD Command request with
TID set to CHOOSE acceptable descriptors (note: e.g. for creation of
a RTP Termination) sends a Transaction reply containing Action reply
with CID set to a specific value (assigned by the MG) ADD Command reply
with TID set to a specific value (assigned by the MG).
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09]
H248_MG_AD_BV_02 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
ADD Command request with
TID set to TID1
acceptable descriptors
sends a Transaction reply containing
Action reply with
CID set to a specific value (assigned by the MG)
ADD Command reply with
TID set to TID1.
Initial condition: A physical termination characterized by TID1, in the NULL Context.
The Physical Termination TID1 shall NOT be in serviceState "outOfService"
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
H248_MG_AD_BV_03 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
ADD Command request with
TID set to ALL(p12)
acceptable descriptors
sends a Transaction reply containing
Action reply with
CID set to a specific value (assigned by the MG)
ADD Command reply with
TID set to TID1
ADD Command reply with
TID set to TID2.
Initial condition: 2 physical Terminations, characterized by TID1 and TID2, each of them in the NULL
Context. The physical Terminations TID1 and TID2 shall not be in serviceState "outOfService".
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
H248_MG_AD_BV_04 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
ADD Command request with
TID set to CHOOSE
acceptable descriptors (note: e.g. for creation of a RTP Termination)
sends a Transaction reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to a specific value (assigned by the MG)
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BV_05 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
ADD Command request with
TID set to ALL(p23)
acceptable descriptors
sends a Transaction reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to TID2
ADD Command reply with
TID set to TID3
Initial condition: 2 physical Termination, characterized by TID2 and TID3, each of them in the NULL
Context and a Termination (TID1) in a Context CID1. The physical Terminations shall NOT be in
serviceState "outOfService".
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BV_06 The termiations TID1 and TID2 shall NOT be in serviceState"outOfService". Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
ADD Command request with
TID set to TID2
sends a Transaction reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to TID2
Initial condition: a physical Termination, characterized by TID2, in the NULL Context and a Termination (TID1) in Context CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BV_07 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
ADD Command request with
TID set to CHOOSE
acceptable descriptors
sends a Transaction reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to TID2
Action reply with
CID set to CID2
ADD Command reply with
TID set to TID4
Initial condition: Initial condition: 2 Terminations (TID1 and TID3) each in a Context characterized by CID1 and CID2 (NULL Context excluded).
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_AD/
MG_AD_BI		 Media gateway termination ADD protocol error compliance test routines.
H248_MG_AD_BI_01 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
ADD Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
ADD Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BI_02 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
ADD Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to CID1
ADD Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BI_03 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
ADD Command request with
TID set to ALL
sends a Transaction reply containing
Action reply with
CID set to ALL
ADD Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BI_04 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
ADD Command request with
TID set to TID1
sends a Transaction reply containing
Action reply with
CID set to ALL
ADD Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BI_05 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
ADD Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to ALL
ADD Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BI_06 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
ADD Command request with
TID set to TID1
sends a Transaction reply containing
Action reply with
CID set to NULL
ADD Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BI_07 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
ADD Command request with
TID set to ALL
sends a Transaction reply containing
Action reply with
CID set to NULL
ADD Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BI_08 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
ADD Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to NULL
ADD Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AD_BI_09 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
ADD Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to NULL
ADD Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_MD
Binary_Mode/
MG/
MG_MD/
MG_MD_BI
H248_MG_MD_BI_01 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
MODIFY Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
MODIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MD_BI_02 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
MODIFY Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
MODIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 Terminations (TID1 and TID2) exist in a Context (CID1).
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MD_BI_03 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
MODIFY Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
MODIFY Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MD_BI_04 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
MODIFY Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 Terminations (TID1 and TID2) exist in a Context (CID1)
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MD_BI_05 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
MODIFY Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to CID1
MODIFY Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 Terminations (TID1 and TID2) exist in a Context (CID1)
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MD_BI_06 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
MODIFY Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to ALL
MODIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 Contexts, characterized by CID1 and CID2 and 2 Terminations characterized by TID1 and TID2 within the Contexts.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MD_BI_07 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
MODIFY Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to ALL
MODIFY Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 existing Contexts, characterized by CID1 and CID2, and 2 Terminations characterized by TID1 and TID2 within the Contexts.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MD_BI_08 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
MODIFY Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to NULL
MODIFY Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 physical Terminations, characterized by TID1 and TID2, in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MD_BI_09 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
MODIFY Command request with
TID set to TID1
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
MODIFY Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 Terminations (TID1 and TID2) exist in a Context CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_SU		 Media gateway termination SUBTRACT compliance verification routines.
Binary_Mode/
MG/
MG_SU/
MG_SU_BV		 Media gateway termination SUBTRACT protocol verification routines.
H248_MG_SU_BV_01 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to ALL(e12)
empty Audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to TID1
SUBTRACT Command reply with
TID set to TID2
Initial condition: 2 Terminations (TID1 and TID2) within a Context CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BV_02 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to ALL(e12)
wildcardReturn request
empty Audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to ALL
Initial condition: 2 Terminations (TID1 and TID2) within a Context CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BV_03 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to TID1
empty Audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to TID1
Initial condition: 2 Terminations (TID1 and TID2) within a Context CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BV_04 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to ALL (e1234)
empty Audit descriptor
wildcardReturn request
sends a Transaction reply containing
Action reply with
CID set to ALL
SUBTRACT Command reply with
TID set to ALL(e1234)
Initial condition: 2 Terminations (TID1 and TID2) are within Context CID1 and 2 Terminations (TID3 and TID4) are in a context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BV_05 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to ALL,
empty Audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to TID1
SUBTRACT Command reply with
TID set to TID2
Action reply with
CID set to CID2
SUBTRACT command reply with
TID set to TID3
SUBTRACT Command reply with
TID set to TID4
Initial condition:2 Terminations (TID1 and TID2) are in a Context CID1 and 2 Terminations (TID3 and
TID4) are in a Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BV_06 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to TID3
empty Audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CID2
SUBTRACT Command reply with
TID set to TID3
Initial condition: 2 Terminations (TID1 and TID2) are within Context CID1 and 2 Terminations (TID3 and TID4) are in a context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_SU/
MG_SU_BI		 Media gateway termination SUBTRACT protocol error compliance verification routines.
H248_MG_SU_BI_01 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_02 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
SUBTRACT Command request with
TID set to ALL
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
SUBTRACT Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: Termination TID1 in Context CID1, Termination TID2 in Context CID2
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_03 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
SUBTRACT Command request with
TID set to TID1
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
SUBTRACT Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: Termination TID1 in Context CID1, Termination TID2 in Context CID2
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_04 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
SUBTRACT Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_05 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: A Termination, characterized by TID1, in a Context characterized by CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_06 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: A Termination, characterized by TID1, in a Context characterized by CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_07 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to ALL
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 exisiting Contexts characteriyed by CID1 and CID2 andTerminations characterized by TID1 and TID2 within the Contexts.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_08 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to ALL
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 Terminations (TID1 and TID2) are in Context CID1, 2 Terminations (TID3 and TID4) are in Context CID2
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_09 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 physical Terminations (TID1 and TID2) exist in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_10 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to ALL
sends a Transaction reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 physical Terminations (TID1 and TID2) exist in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_11 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to TID1
sends a Transaction reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 physical Terminations (TID1 and TID2) exist in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SU_BI_12 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 physical Terminations (TID1 and TID2) exist in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_MO		 Media gateway termination MODIFY protocol compliance test routines.
Binary_Mode/
MG/
MG_MO/
MG_MO_BV		 Media gateway termination Modify compliance verification routines.
H248_MG_MO_BV_01 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID2
MOVE Command request with
TID set to TID2,
acceptable descriptors
sends a Transaction reply containing
Action reply with
CID set to CID2
MOVE Command reply with
TID set to TID2
Initial condition: 2 Terminations (TID1 and TID2) within a Context CID1, 2 Terminations (TID3 and
TID4) in Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_MO/
MG_MO_BI		 Media gateway termination MODIFY protocol error compliance verification routines.
H248_MG_MO_BI_01 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
MOVE Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
MOVE Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_02 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
MOVE Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
MOVE Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_03 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: A Termination, characterized by TID1, in a Context characterized by CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_04 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
SUBTRACT Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to CID1
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: A Termination, characterized by TID1, in a Context characterized by CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_05 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to ALL
sends a Transaction reply containing
Action reply with
CID set to ALL
SUBTRACT Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_06 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to ALL
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_07 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to TID1
sends a Transaction reply containing
Action reply with
CID set to ALL
SUBTRACT Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_08 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to ALL
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_09 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to CHOOSE
sends a Transaction reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 physical Terminations (TID1 and TID2) exist in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_10 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to ROOT
sends a Transaction reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 physical Terminations (TID1 and TID2) exist in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_11 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to ALL
sends a Transaction reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 physical Terminations (TID1 and TID2) in Context CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_MO_BI_12 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
SUBTRACT Command request with
TID set to TID1
sends a Transaction reply containing
Action reply with
CID set to NULL
SUBTRACT Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error".
Initial condition: 2 physical Terminations (TID1 and TID2) in Context CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_AC_BI
H248_MG_AC_BI_01 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
AUDIT CAPABILITIES Command request with
TID set to CHOOSE
acceptable audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
Audit Capabilities Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error").
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AC_BI_02 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
AUDIT CAPABILITIES Command request with
TID set to ALL
acceptable audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
Audit Capabilities Command reply with
TID set to ALL
Error descriptor (e.g. value 401, "Protocol Error").
Initial condition: 2 Terminations (TID1, TID2) in Context CID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AC_BI_03 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
AUDIT CAPABILITIES Command request with
TID set to TID1
acceptable audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
Audit Capabilities Command reply with
TID set to TID1
Error descriptor (e.g. value 401, "Protocol Error").
Initial condition: 2 Terminations (TID1, TID2) in Context CID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AC_BI_04 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CHOOSE
AUDIT CAPABILITIES Command request with
TID set to ROOT
acceptable audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CHOOSE
Audit Capabilities Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error").
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AC_BI_05 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
AUDIT CAPABILITIES Command request with
TID set to CHOOSE
acceptable audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CID1
Audit Capabilities Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error").
Initial condition: a Termination characterized by TID1 in a Context characterized by CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AC_BI_06 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to CID1
AUDIT CAPABILITIES Command request with
TID set to ROOT
acceptable audit descriptor
sends a Transaction reply containing
Action reply with
CID set to CID1
Audit Capabilities Command reply with
TID set to ROOT
Error descriptor (e.g. value 401, "Protocol Error").
Initial condition: a Termination characterized by TID1 in a Context characterized by CID1.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AC_BI_07 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to ALL
AUDIT CAPABILITIES Command request with
TID set to CHOOSE
acceptable audit descriptor
sends a Transaction reply containing
Action reply with
CID set to ALL
Audit Capabilities Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error").
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AC_BI_08 Ensure that the IUT, on receipt of a Transaction request containing
Action request with
CID set to NULL
AUDIT CAPABILITIES Command request with
TID set to CHOOSE
acceptable audit descriptor
sends a Transaction reply containing
Action reply with
CID set to NULL
Audit Capabilities Command reply with
TID set to CHOOSE
Error descriptor (e.g. value 401, "Protocol Error").
Initial condition: 2 Terminations (TID1 and TID2) in the NULL Context.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_NO_BV
H248_MG_NO_BV_01 Ensure that the IUT, in order to indicate the detected event(s), sends a Transaction Request containing
Action request with
CID set to CID1
NOTIFY Command request with
TID set to TID1
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events
Initial condition: an Events descriptor with specific RequestID was set at the IUT for a specific Termination (TID1) in a specific Context (CID1) . The IUT has detected the Event(s).
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_NO_BV_02 Ensure that the IUT, in order to indicate the detected event(s), sends a Transaction Request containing
Action request with
CID set to NULL
NOTIFY Command request with
TID set to TID1
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events
Initial condition: an Events descriptor with specific RequestID was set at the IUT for a specific physical Termination (TID1) in the NULL Context. The IUT has detected the Event(s).
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_NO_BV_03 Ensure that the IUT, in order to indicate the detected event(s), sends a Transaction Request containing
Action request with
CID set to NULL
NOTIFY Command request with
TID set to ROOT
ObservedEvents Descriptor
specific RequestID
acceptable list of observed events
Initial condition: an Events descriptor with specific RequestID was set at the IUT for the ROOT Termination. The IUT has detected the Event(s).
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_SC_BV
H248_MG_SC_BV_01 Ensure that the IUT, in order to indicate that a specific Termination (TID1) in a Context (CID1) will be taken out of service after a specified ServiceChangeDelay, sends a Transaction Request containing
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 905("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_02 Ensure that the IUT, in order to indicate that a specific Termination (TID1) in a Context (CID1) will be taken out of service after a specified ServiceChangeDelay, sends a Transaction Request containing
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 905("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_03 Ensure that the IUT, in order to indicate that a specific Termination (TID1) in a Context (CID1) will be taken out of service after a specified ServiceChangeDelay, sends a Transaction Request containing
Action request with
CID set to ALL
SERVICE CHANGE Command request with
TID set to ALL(e1234)
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 905 ("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_04 Ensure that the IUT, in order to indicate that a specific Termination (TID1) in a Context (CID1) will be taken out of service after a specified ServiceChangeDelay, sends a Transaction Request containing
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 905("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
Initial condition: 2 Terminations (TID1 and TID2) in the NULL Context
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_05 Ensure that the IUT, in order to indicate that a specific Termination (TID1) in a Context (CID1) will be taken out of service after a specified ServiceChangeDelay, sends a Transaction Request containing
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 905("Termination taken out of service")
ServiceChangeDelay set to a specific value (TSC_SCDtime)
Initial condition: 2 Terminations (TID1 and TID2) in the NULL Context
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_06 Ensure that the IUT, in order to indicate that the whole MG will be taken out of service after a specified ServiceChangeDealy , sends a Transaction Request containing
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Graceful
ServiceChangeReason set to value 908("MG Impending Failure")
ServiceChangeDelay set to a specific value
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_07 Ensure that the IUT, in order to indicate that a specific Termination (TID1) in a Context (CID1) will be taken out of service after a specified ServiceChangeDelay, sends a Transaction Request containing
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 905("Termination taken out of service")
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_08 Ensure that the IUT, in order to indicate that all Terminations (TID1 and TID2) within a specific Context (CID1) will be taken out of service after a specified ServiceChangeDelay, sends a Transaction Request containing
Action request with
CID set to CID1
SERVICE CHANGE Command request with
TID set to ALL(e12)
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 905("Termination taken out of service")
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_09 Ensure that the IUT, in order to indicate that all Terminations within all Contexts will be taken out of service after a specified ServiceChangeDelay, sends a Transaction Request containing
Action request with
CID set to ALL
SERVICE CHANGE Command request with
TID set to ALL(e1234)
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 905("Termination taken out of service")
Initial condition: 2 Terminations (TID1 and TID2) in Context CID1, 2 Terminations (TID3 and TID4) in Context CID2
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_10 Ensure that the IUT, in order to indicate that Termination TID1 will be taken out of service after a specified ServiceChangeDelay, sends a Transaction Request containing
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 905("Termination taken out of service")
Initial condition: 2 Terminations (TID1 and TID2) in the NULL Context
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_11 Ensure that the IUT, in order to indicate that the Terminations TID1 and TID2 will be taken out of service after a specified ServiceChangeDelay, sends a Transaction Request containing
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ALL
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 905("Termination taken out of service")
Initial condition: 2 Terminations (TID1 and TID2) in the NULL Context
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_12 Ensure that the IUT, in order to indicate that the whole MG will be taken immediately out of service, sends a Transaction Request containing
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change Descriptor
ServiceChangeMethod set to Forced
ServiceChangeReason set to value 908("MG Impending Failure")
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_13 Ensure that the IUT, in order to indicate that service will be restored for all Terminations (TID1 and TID2) in the NULL context, sends a Transaction Request containing
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ALL(p12)
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeReason set to value 900("Service Restored")
Initial condition: 2 physical Terminations (TID1 and TID2) in the NULL Context and which are out of service.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_SC_BV_14 Ensure that the IUT, in order to indicate that service will be restored for TerminationTID1 in the NULL context, sends a Transaction Request containing
Action request with
CID set to NULL
SERVICE CHANGE Command request with
TID set to TID1
Service Change Descriptor
ServiceChangeMethod set to Restart
ServiceChangeReason set to value 900("Service Restored")
Initial condition: 2 physical Terminations (TID1 and TID2) in the NULL Context and which are out of service.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_AM_BV
H248_MG_AM_BV_01 Ensure that the IUT, upon cold start,sends a Transaction Reply containing
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeMethod set to Restart
Initial condition: idle
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AM_BV_02 Ensure that the IUT, upon cold start,sends a Transaction Reply containing
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with TimeStamp
Initial condition: idle
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AM_BV_03 Ensure that the IUT, upon cold start,sends a Transaction Reply containing
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeReason set to 901 ("Cold Boot")
Initial condition: idle
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AM_BV_04 Ensure that the IUT, upon cold start, in order to indicate a new address for subsequent communication, sends a Transaction Reply containing
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeAddress (for further communication)
Initial condition: idle
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AM_BV_05 Ensure that the IUT, on receipt of a Transaction Reply containing
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeMgcId
Initial condition: IUT has sent a valid Transaction Request to perform a cold start (e.g. ServiceChangeCommand request with the ServiceChangeMethod set to RESTART).
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AM_BV_06 Ensure that the IUT, after timer expiry without having received the appropriate Transaction Reply form its primary MGC resends the valid Transaction Request to its secondary MGC to perfom a cold start
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AM_BV_07 Ensure that the IUT, upon cold start, having sent a ServiceChangeCommand request with the ServiceChangeMethod parameter set to "RESTART", on receipt of a message other than the corresponding ServcieChange Command reply, the IUT sends a Transaction Reply containing error descriptor (value 505, "Command received before Restart Response")
Initial condition: idle
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AM_BV_08 Ensure that the IUT, upon cold start,sends a Transaction Request containing
Action reply with
CID set to NULL
SERVICE CHANGE Command request with
TID set to ROOT
Service Change descriptor with
ServiceChangeVersion set to 2
Initial condition: idle
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AM_BV_09 Ensure that the IUT, on receipt of a Transaction Reply containing
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeVersion set to 3
rejects subsequent Transaction Request with a Transaction Reply message containing error descriptor (value 406, "Version not supported")
Initial condition: IUT has sent a valid Transaction Request to perform a cold start (e.g. ServiceChangeCommand request with the ServiceChangeMethod set to RESTART).
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AM_BV_10 Ensure that the IUT, on receipt of a Transaction Reply containing
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeMethod set to Handoff
ServiceChangeReason set to 903("MGC directed change")
ServiceChangeMgcId to the designated MGC address
sends a Transaction Reply containing
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Initial condition: any.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_AM_BV_11 Ensure that the IUT, in order to establish a new connection to the designated MGC, sends a Transaction Reply containing
Action reply with
CID set to NULL
SERVICE CHANGE Command reply with
TID set to ROOT
Service Change descriptor with
ServiceChangeMethod set to handOff
ServiceChangeReason set to 903("MGC directed change")
Initial condition: IUT received a Service Change Command request with ServiceChangeMethod set to Handoff together with a designated MGC address.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_TR_BV
H248_MG_TR_BV_01 Ensure that the IUT, on receipt of a Megaco message containing
Transaction Request with
TransID set to a TransID1
acceptable Action request and Command request
sends a Megaco message containing
Transaction reply with
TransID set to a TransID1
acceptable Action reply and Command reply
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MG/
MG_TR_BV/
MG_TR_BV
H248_MG_TR_BV_02 Ensure that the IUT, on expiry of the Transaction Timer without receipt of the corresponding Transaction Response Acknowledge, resends the previous Transaction Reply
Initial condition: After the receipt of a valid Transaction Request the IUT has sent a valid Transaction Reply.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_TR_BV_03 Ensure that the IUT, on receipt of a Megaco message containing
Transaction Reply with
TransID set to a TransID1
acceptable Action reply and Command reply
sends a Megaco message containing
Transaction Response Acknowledge with
TransID set to a TransID1
Initial condition: IUT has sent a valid Transaction Request with a Transaction ID set to TransID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_TR_BV_04 Ensure that the IUT, on expiry of the Transaction Timer without receipt of neither a Transaction Reply nor a Transaction Pending, resends the previous Transaction Request
Initial condition: IUT has sent a valid Transaction Request with a Transaction ID set to TransID1
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_TR_BV_05 Ensure that the IUT, on expiry of the Transaction Timer without receipt of the corresponding Transaction Reply or another Transaction Pending, resends theTransaction Request
Initial condition: After sending a valid Transaction Request the IUT has received a valid Transaction Pending.
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_TR_BV_06 Ensure that the IUT, on receipt of a Megaco message containing
Transaction Reply with
TransID set to a TransID1
acceptable Action reply and Command reply
sends a Megaco message containing
Transaction Response Acknowledge with
TransID set to a TransID1
Initial condition: After sending a valid Transaction Request the IUT has received a valid Transaction Pending
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Binary_Mode/
MGC
H248_MGC_Startup_V_01 Send ServiceChangeReq, wait for response
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1]
H248_MGC_V_001 Initiate Cold Sync procedure and ensure IUT sends ServiceChangeReply
followed by ModifyReq.
IUT: MGC
User Action: None
Misc
Megaco_MG_V_101 Waits for MG to send ServiceChangeReq, send Reply in response
Waits for MG to send ServiceChangeReq, send Reply in response
Megaco_MG_V_102 Waits for MG to send ServiceChangeReq, send Reply in response
Waits for MG to send ServiceChangeReq, send Reply in response
Megaco_MG_DS_DSP Tests the Diff Serv Package - Sends a Modify with the DSP Package Encoded
Tests the Diff Serv Package - Sends a Modify with the DSP Package Encoded
Megaco_MG_TXT_Start_03_AUTH Wait for ServiceChangeReq, send response with AUTH Header, est. connection
the tester and the SUT.
Initial condition: any
User Action: Generate a Service Change event, "Cold Reboot"
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1]
Megaco_MG_TrafficManagement Tests the Traffic Management Package - Sends a Modify with the TMAN Package Encoded
Tests the Traffic Management Package - Sends a Modify with the TMAN Package Encoded
Megaco_MGC_V_001 Initiate Cold Sync procedure and ensure IUT sends ServiceChangeReply
followed by ModifyReq.
IUT: MGC
User Action: None
Megaco_MGC_V_002 Send Notify Offhook to IUT
SUT: MGC
User Action: None
Megaco_MG_V_001 Send ModifyReq off-hook
IUT: MG
User Action: None
H248_MG_ADD_AND_RING Ensure that the IUT, on receipt of a Transaction request containing
Action request with CID set to CHOOSE ADD Command request with
TID set to CHOOSE acceptable descriptors (note: e.g. for creation of
a RTP Termination) sends a Transaction reply containing Action reply
with CID set to a specific value (assigned by the MG) ADD Command reply
with TID set to a specific value (assigned by the MG).
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_ADD_RING_NOTIFY Attempt to ring an endpoint and tie up an RTF stream
Initial condition: any
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MG_ADD Send AddReq
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
H248_MGC_NOTIFY Send NotifyReq
User Action: None
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: 7.2.1 ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09
12.2.2 [1]
Megaco_Connect_Text To simulate a connected call. Phone will ring and when phone is picked up, two phones should be connected.
To simulate a connected call. Phone will ring and when phone is picked up, two phones should be connected.
Megaco_Call_Flow_Text To simulate a call flow. Phone will ring and when phone is picked up, a dialtone will be heard and digits received.
To simulate a call flow. Phone will ring and when phone is picked up, a dialtone will be heard and digits received.
Megaco_CISCO_ADD_Text To simulate a CISCO ADD trace. It will do a cisco add and then subtract it.
To simulate a CISCO ADD trace. It will do a cisco add and then subtract it.
Megaco_CISCO_ADD_2_Text To simulate a CISCO ADD trace with new parameters. It will do a cisco add and then subtract it.
To simulate a CISCO ADD trace with new parameters. It will do a cisco add and then subtract it.
Megaco_CISCO_ADD_W_TERMSTATE_Text To simulate a CISCO ADD with TerminationState trace. It will do a cisco add for a fax relay and then subtract it.
To simulate a CISCO ADD with TerminationState trace. It will do a cisco add for a fax relay and then subtract it.
Encode_Priority_Message_Text To test the encoding of a priority message.
To test the encoding of a priority message.
Raw_Message_Test_01 Sends a raw message
Sends a raw message
Raw_Message_Test_02 Sends a raw message
Sends a raw message
H248_MGC_TXT_AD_BV_01_test To be used with H248_MGC_TXT_AD_BV_01
Sends a Transaction request containing
Action request with
CID set to CHOOSE
ADD Command request with
TID set to CHOOSE
acceptable descriptors (note: e.g. for creation of
a RTP Termination)
Should receive a Transaction reply containing
Action reply with
CID set to a specific value (assigned by the MG)
ADD Command reply with
TID set to a specific value (assigned by the MG).

Should clean up test with a Transaction request containing
Action request with
CID set to ALL
SUBTRACT Command request with
TID set to ALL
Megaco_2_link_test_01 Send AddReq on two links.
Send AddReq on two links.
Japan_demo_call_flow To simulate a specific call flow; Service Change --> Modify --> Notify --> Add --> Subtract.
To simulate a specific call flow; Service Change --> Modify --> Notify --> Add --> Subtract.
ASB_demo_call_flow To simulate a specific call flow; Call Waiting
To simulate a specific call flow; Call Waiting
Megaco_Loop_Test_txt To simulate a specific call flow and keep looping; Add --> Modify --> Subtract --> Add etc
To simulate a specific call flow and keep looping; Add --> Modify --> Subtract --> Add etc
H248_v3_MG_TXT_AV_BV_01 Init: 2 eph term=TID1,TID2 in CID=CID1, 2 eph term=TID3,TID4 in CID=CID2. Test: Send Transaction Rq Audit Value, CID=ALL, TID=ALL
Initial condition: 2 Terminations (TID1, TID2) in a Context CID1,
2 Terminations (TID3, TID4) in a Context CID2

Ensure that the IUT, on receipt of a Transaction Request containing
Action request with
CID set to ALL
AUDIT VALUE Command request with
TID set to ALL
acceptable Audit Descriptor

sends a segmented Transaction Reply of two segments,
the first segment containing:
Action reply with
CID set to CID1
AUDIT VALUE Command reply with
TID set to TID1
AUDIT VALUE Command reply with
TID set to TID2

the second segment containing:
Action reply with
CID set to CID2
AUDIT VALUE Command reply with
TID set to TID3
AUDIT VALUE Command reply with
TID set to TID4
2 Terminations (TID3, TID4) in a Context CID2
User Action: None
Config: Config1
SUT: MG or PG
Status:
Ref: H.248.1v3
H248_v3_MGC_TXT_AV_BV_01 Initial condition: 2 Terminations (TID1 and TID2) exist in Context CID1,
2 Terminations (TID3 and TID4) exist in Context CID2.
Ensure that the IUT, in order to get the current values of parameters for all Terminations
within all Contexts, sends a Transaction Request containing:
Action request with
CID set to ALL
AUDIT VALUE Command request with
TID set to ALL
acceptable Audit Descriptor
2 Terminations (TID3 and TID4) exist in Context CID2.
User Action: Generate a Audit Value Request to get current values for all Terminations in all Contexts.
Config: Config1
SUT: MGC
Status:
Ref: H.248.1v3
Debug_Start_01 Wait for ServiceChangeReq, send response, est. connection
the tester and the SUT.
Initial condition: any
User Action: Generate a Service Change event, "Cold Reboot"
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1]
Debug_Start_02 Wait for ServiceChangeReq, send response, est. connection
the tester and the SUT.
Initial condition: any
User Action: Generate a Service Change event, "Cold Reboot"
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1]
Raw_Message_Test_09 Sends a raw message
Sends a raw message
Raw_Message_Test_10 Sends a raw message for David Higgins May 4th
Sends a raw message for David Higgins May 4th
Call_Waiting_Indication Sends Call Waiting Indication
Sends Call Waiting Indication
Subtract_Request_W_Audit Sends a Subtract Request with an Empty Audit
Sends a Subtract Request with an Empty Audit
H248_MG_TXT_Zhone_GW_01 Wait for ServiceChangeReq, send response, est. connection
the tester and the SUT, ZhoneGW.
Initial condition: any
User Action: Generate a Service Change event, "Cold Reboot"
Config: Config1
SUT: MG or PG
Status: Mandatory
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1]
H248_MGC_TXT_Huawei_GW_01 Send Notify off-hook to act as Huawei GW towards MGC.
User Action: Generate a Service Change event, "Cold Reboot"
Config: Config1
SUT: MGC
Status: Optional
Ref: ACATS Megaco v2.0 (ETSI-TS-102-374-2 v1.1.1 (2004-11)) / ITU-T H.248.1 2005-09 [1]
H248_MGC_TXT_Huawei_GW_02 Generated scenario from a trace
Generated scenario from a trace

Variable Default Value Description
TSPX_MId_tester "192.168.1.57" The IP address of the tester for Link 1. Can be one of the following : ip4Address ip6Address
TSPX_MId_use_domain FALSE Set this to True when using DomainName instead of IP address in Megaco messages. If set to TRUE, fill in value TSPX_MId_domain_tester
TSPX_MId_domain_tester "" Set this to variable to the domain name of the Tester when TSPX_MId_use_domain is set to TRUE.
TSPX_MId_IUT "192.168.1.7" The IP address of the system under test for Link 1.
TSPX_MId_tester2 "192.168.1.62" The IP address of the tester for Link 2. Can be one of the following : ip4Address ip6Address domainName deviceName mtpAddress
TSPX_MId_IUT2 "192.168.1.7" The IP address of the system under test for Link 1.
TSPX_KEEPALIVE_ON FALSE Set to TRUE to send/reply to AuditValue keep alive messages. Set to FALSE is keep alive messages are not used.
TSPX_KEEPALIVE_AUDIT_DESCRIPTOR1 "" When TSPX_KEEPALIVE_ON=TRUE, contains the name of the 1st descriptor in the AuditValue Request(MG tests)/ Reply(MGC tests) message sent
TSPX_KEEPALIVE_AUDIT_VALUE1 "" When TSPX_KEEPALIVE_ON=TRUE, contains the value of the 1st descriptor in the AuditValue Request(MG tests)/ Reply(MGC tests) message sent
TSPX_KEEPALIVE_AUDIT_DESCRIPTOR2 "" When TSPX_KEEPALIVE_ON=TRUE, contains the name of the 2nd descriptor in the AuditValue Request(MG tests)/ Reply(MGC tests) message sent
TSPX_KEEPALIVE_AUDIT_VALUE2 "" When TSPX_KEEPALIVE_ON=TRUE, contains the value of the 2nd descriptor in the AuditValue Request(MG tests)/ Reply(MGC tests) message sent
TSPX_PG_Mode FALSE Set to TRUE if testing a Packet Gateway
TSPX_TESTER_PORT 2944 The port used by the tester to send or receive MEGACO messages. DEFAULT value is 2945 for BER AND 2944 for text ENCODE
TSPX_TESTER_NEW_PORT 20001 Change to this in ServiceChangeReply if TGW_Mode TRUE
TSPX_SUT_PORT 2944 The port used by the system under test to send or receive MEGACO messages. Value is normalling 2945 for BER AND 2944 for text ENCODE
PX_Transport Transport_Param_UDP Transport used for Megaco
PX_TCP_Mode TCP_MGT_Server Set to TCP_MGT_Client if tester is to initiate outgoing connection. Otherwise, set to TCP_MGT_Server.
Use_AuthHeader FALSE Set to TRUE if an Authentication Header is needed in MEGACO messages.
PX_AuthHeader "AU=0x00000000:0x00000000:0x00... When Use_AuthHeader is true, this authentication string will be added to the frame
PX_Version_Number 2 The version of MEGACO to use in the tests.
PX_Version_Number_Invalid "3" Invalid H.248 Version Number used in AM_BV_09, (recommended value PX_Version_Number + 1)
SCTP_Mode FALSE Set this parameter to TRUE to use SCTP network protocol when running tests.
N_Output_Streams 1 The number of output streams used in SCTP communications.
N_Input_Streams 1 The number of input streams used in SCTP communications.
PCO1_Adaptor_ID 1 The adaptor ID for the network adapter.
N_Adaptors 1 The number of network adapters.
N_Sockets 1 The number of SCTP associations to use.
Layer_3_Protocol Use_IPv4 Network layer; above Ethernet, default = Use_IPv4
TSPX_TID_CHOOSE_EPH_text "$" When testing MGs/PGs, the ephermeral Termination ID with CHOOSE wildcard for 2 ephemeral (temporary) terminations
TSPX_TID_CHOOSE_PHY_text "$" When testing MGs/PGs, the physical Termination ID with CHOOSE wildcard for 2 physical terminations
TSPX_TID1_text "line/1" A valid Physical Termination ID (referenced as physical Termination TID1 in the TPs)
TSPX_TID2_text "line/2" A valid Physical Termination ID (referenced as physical Termination TID2 in the TPs)
TSPX_TID3_text "line/3" A valid Physical Termination ID (referenced as physical Termination TID3 in the TPs)
TSPX_TID4_text "line/4" A valid Physical Termination ID (referenced as physical Termination TID4 in the TPs)
TSPX_TID_EPH_1_text "rtp/1" Ephemeral Termination ID 1 string to use in MGC tests
TSPX_TID_EPH_2_text "rtp/2" Ephemeral Termination ID 2 string to use in MGC tests
TSPX_TID_EPH_3_text "rtp/3" Ephemeral Termination ID 3 string to use in MGC tests
TSPX_TID_EPH_4_text "rtp/4" Ephemeral Termination ID 4 string to use in MGC tests
TSPX_TID_ALL_EPH_text "*" Termination ID with ALL wildcard which addresses ephemeral Terminations TID1 and TID2
TSPX_TID_ALL_PHY_2_C1 "line/*" Termination ID with ALL wildcard which addresses physical Terminations TID1 and TID2
TSPX_TID_ALL_PHY_2_C2 "line/*" Termination ID with ALL wildcard which addresses physical Terminations TID3 and TID4
TSPX_TID_ALL_PHY_2_text "line/*" Termination ID with ALL wildcard which addresses 2 physical Terminations TID1 and TID2
TSPX_TID_ALL_text "*" Termination ID with NULL wildcard for both, ephemeral and physical Terminations
TSPX_Audit_text "Media" The audit descriptor(s) to use in the tests. Separate descriptor names with a comma (,).
TCV_Audit_Root_text "Statistics" The audit descriptor(s) to use in the tests for Root Terminations. Separate descriptor names with a comma (,).
TCV_Request_ID "1234" The Request ID for the Events Descriptor
TSPX_EVENTS_DESC_EPH "al/of" All the Events Descriptors in proper syntax text format for an Ephemeral Termination
TSPX_EVENTS_DESC_PHY "al/of" All the Events Descriptors in proper syntax text format for a Physical Termination
TSPX_EVENTS_DESC_ROOT "al/of" All the Events Descriptors in proper syntax text format for a ROOT Termination
TSPX_OBSERVED_EVENTS_DESC_EPH_TXT "al/of" The event(s) to generate in MGC tests, for Notify tests for ephemeral terminations.
TSPX_OBSERVED_EVENTS_DESC_PHY_TXT "al/of" The event(s) to generate in MGC tests, for Notify tests for physical terminations.
TSPX_OBSERVED_EVENTS_DESC_ROOT_TXT "al/of" The event(s) to generate in MGC tests, for Notify tests for ROOT terminations.
TCV_Signals_Desc "al/ri" All the Signals Descriptors in proper syntax text format
TSPX_ServiceChangeAddress_Included FALSE Set to TRUE if including port in ServiceChangeAddress field, FALSE by default.
TSC_SCDtime "2" The ServiceChange Delay time to use in ServiceChange messages.
TCV_SCMgcId "[192.1.168.62]:2944" The ServiceChange MgcId to use in ServiceChange messages.
TCV_Notify_StreamID "1" The stream ID of the event the Notify is indicating
TSPX_LONG_TIMER 4000 The LONG_TIMER indicating maximum secs allowed before resending a reply message.
TSPX_SHORT_TIMER 0 The SHORT_TIMER indicating minimum time to pass before resending a reply message.
TSPX_NormalMGCExecutionTime 30000 The time which indicates the interval that the MG expects a response from the MGC.
TSPX_ADD_MEDIA_Mode_DESC_EPH_1_text "SendReceive" The Mode value for the Media descriptor for the 1st ephemeral termination in Add messages.
TSPX_ADD_MEDIA_Mode_DESC_EPH_2_text "SendReceive" The Mode value for the Media descriptor for the 2nd ephemeral termination in Add messages.
TSPX_MODIFY_MEDIA_Mode_DESC_PHY_text "" The Mode value for the Media descriptor for the 1st physical termination in Modify messages in Notify tests.
TSPX_MODIFY_Audit_PHY_text "" The value to Audit for the 1st physical termination in Modify messages in Notify tests.
USER_LCDM1_TOKEN_TXT "" Custom Amm parameter
USER_LCDM1_VALUE_TXT "" Custom Amm parameter
USER_LCDPP1_NAME1_TXT "" Custom Amm parameter
USER_LCDPP1_VALUE1_TXT "" Custom Amm parameter
USER_LDN1_NAME1_TXT "" Custom Amm parameter
USER_LDN1_VALUE1_TXT "" Custom Amm parameter
USER_LDN1_NAME2_TXT "" Custom Amm parameter
USER_LDN1_VALUE2_TXT "" Custom Amm parameter
USER_LDN1_NAME3_TXT "" Custom Amm parameter
USER_LDN1_VALUE3_TXT "" Custom Amm parameter
USER_LDN1_NAME4_TXT "" Custom Amm parameter
USER_LDN1_VALUE4_TXT "" Custom Amm parameter
USER_LCDM2_TOKEN_TXT "" Custom Amm parameter
USER_LCDM2_VALUE_TXT "" Custom Amm parameter
USER_LCDPP2_NAME1_TXT "" Custom Amm parameter
USER_LCDPP2_VALUE1_TXT "" Custom Amm parameter
USER_TID1_TXT "" Custom Amm parameter
PX_TerminationId_Root 'FFFFFFFFFFFFFFFF'H Used in binary mode tests. The ROOT termination ID to use in tests.
PX_Profile_Name "GW" Used in binary mode tests. The Profile Name to use in tests.
PX_Media_Address "10.12.21.233" Used in binary mode tests. The IP address to use in the Media descriptor.
PX_Termid1 "line/1" Used in binary mode tests. The termination ID to use in tests.
PX_Profile "ResGW/1" Used in binary mode tests. The profile string to use in ServiceChange messages.
TSPX_TID_ALL 'FFFFFFFF'H Termination ID with NULL wildcard for both, ephemeral and physical Terminations
TSPX_TID_ALL_EPH 'FFFFFFFF'H Termination ID with NULL wildcard for both, ephemeral and physical Terminations
TSPX_AV_AUDIT_DESC_ROOT 'FFFFFFFFFFFFFFFF'H The audit descriptor to use for the ROOT termination
TSPX_AV_AUDIT_DESC_EPH 'FFFFFFFFFFFFFFFF'H The audit descriptor to use for the ephemeral termination
TSPX_TID_CHOOSE_PHY 'FFFFFFFFFFFFFFFF'H Physical Termination ID with CHOOSE wildcard for ephemeral (temporary) terminations
TSPX_TID_CHOOSE_EPH 'FFFFFFFE'H Ephermeral Termination ID with CHOOSE wildcard for ephemeral (temporary) terminations
TSPX_TID1 '00000001'H Physical Termination ID (referenced as physical Termination TID1 in the TPs)
TSPX_TID2 '00000002'H Physical Termination ID (referenced as physical Termination TID2 in the TPs)
TSPX_TID3 '00000003'H Physical Termination ID (referenced as physical Termination TID3 in the TPs)
TSPX_TID4 '00000004'H Physical Termination ID (referenced as physical Termination TID4 in the TPs)
TSC_TID_ROOT 'FFFFFFFFFFFFFFFF'H The ROOT termination in binary mode tests.
Ip_Address (null) IP address to use in binary mode tests
Ip_Port 55555 IP port to use in binary mode tests
Event_Request_ID '5555'H Event request ID to use in binary mode tests
Mgc_Termination_Id "a4444" first modify request id
Termination_1 (null) Termination ID 1 to use in binary mode tests.
Termination_2 (null) Termination ID 2 to use in binary mode tests.
T_Active_VAL 5000 Timer value for T_Active timer.

Copyright © ACATS Forum 2008 on behalf of the test suite author. All rights reserved. Specifications may change subject to requirements.

08 Dec 2008 Produced by SAFIRE V20.05.14.01
www.SAFIRE-World.com		 Test Suite Overview